Need help?Do you have a question about the Honeywell XENON 1900 and is the answer not in the manual?
General| Type | Handheld bar code reader |
|---|---|
| Sensor type | Laser |
| Scanner type | 1D/2D |
| Pitch reading angle | -45 - 45 ° |
| Linear (1D) barcodes supported | - |
| Standard interfaces | USB, Keyboard wedge, RS-232, RS-485 |
| Connectivity technology | Wired |
| Input voltage | 4 - 5.5 V |
| Power consumption | 450 mA |
| Power source type | DC |
| Power consumption (standby) | 0.45 W |
| Power consumption (typical) | 2.3 W |
| Shockproof | Yes |
| Product color | Black |
| International Protection (IP) code | IP41 |
| Storage temperature (T-T) | -20 - 70 °C |
| Operating temperature (T-T) | 0 - 50 °C |
| Operating relative humidity (H-H) | 0 - 95 % |
| Sustainability certificates | RoHS |
Weight and Dimensions| Depth | 104 mm |
|---|---|
| Width | 71 mm |
| Height | 160 mm |
| Weight | 147 g |
Device compliance with FCC Rules Part 15 Subpart B Class B.
Class B digital apparatus compliance with Canadian ICES-003.
Honeywell compliance with Directive 2002/96/EC on waste electrical and electronic equipment (WEEE).
Product marked with GS symbol indicating compliance to EN 60950-1.
Statement indicating conformity to AS/NZS 3548 EMC requirement.
Certificate indicating compliance with Gost-R requirements.
Scanner LEDs tested and classified as EXEMPT RISK GROUP per IEC 62471:2006.
Certification to CB Scheme IEC 60950-1, Second Edition.
Statement on product containing a laser engine or aimer, including compliance.
Xenon 1900 has IP41 rating, immunity to foreign particles and dripping water.
Device compliance with FCC Rules Part 15 Subpart C.
Scanner compliance with Canadian RSS-210.
Honeywell compliance with Directive 2002/96/EC on waste electrical and electronic equipment (WEEE).
Product marked with GS symbol indicating compliance to EN 60950-1.
Statement indicating conformity to AS/NZS 3548 EMC requirement.
Product approved by Anatel according to Resolution No. 242/2000.
Certificate for SRRC radio compliance.
Compliance with Technical Regulations Conformity Certification of Specified Radio equipment.
Product meets Korean agency approval.
Conformance to NOM-019.
Product meets Cofetel approval.
Certificate indicating compliance with Gost-R requirements.
Taiwan agency approval based on BSMI Standard CNS13438, CNS14336.
Taiwan NCC standard for low power frequency electric machineries: LP0002.
Scanner LEDs tested and classified as EXEMPT RISK GROUP per IEC 62471:2006.
Bluetooth Class II radio technology information.
Certification to CB Scheme IEC 60950-1, Second Edition.
Statement on product containing a laser engine or aimer, including compliance.
Device compliance with FCC Rules Part 15 Subpart B Class B.
Class B digital apparatus compliance with Canadian ICES-003.
Applies Canadian ISM standard CNR-210.
Honeywell compliance with Directive 2002/96/EC on waste electrical and electronic equipment (WEEE).
Statement indicating conformity to AS/NZS 3548 EMC requirement.
Certificate indicating compliance with Gost-R requirements.
Scanner LEDs tested and classified as EXEMPT RISK GROUP per IEC 62471:2006.
Granit 1911i has IP65 rating, protected against dust and dripping water.
Provides installation and programming instructions for various Honeywell scanners.
Steps for safely unpacking the scanner and checking contents.
Instructions on connecting the scanner to a computer via USB, Keyboard Wedge, and RS232.
Describes how to program the scanner for the desired interface.
Instant scanner setup for common interfaces using Plug and Play bar codes.
Configures scanner for IBM PC AT and compatible keyboard wedge interface.
Enables scanner operation with laptop's integral keyboard.
Allows breaking up large bar code data into smaller packets for IBM POS terminals.
Specifies the data 'packet' size sent to the host when using Packet mode.
Controls CTS/RTS emulation for serial communication.
Configures ACK/NAK mode for scanner communication.
Sets the data transmission rate between scanner and terminal.
Scanner asserts RTS when data is ready, waits indefinitely for CTS.
Scanner asserts RTS for host transmit; host asserts CTS for device transmit.
Scanner asserts RTS, waits for CTS with a delay; resets if timeout expires.
Explains the function of cordless charge base or Access Point for scanner link and data exchange.
Procedure to link a scanner to a charge base for initial setup and charging.
Scanner battery status check and automatic detection for linking to base.
Describes scanner losing communication with base/Access Point and resulting error tone.
Procedure for scanner relinking when it returns within range.
Scanner stores symbols out of range and sends them when back in range.
Configures scanner and base to beep upon power up.
Configures scanner to beep upon receiving a BEL character from host.
Enables or disables an audible click when the scanner trigger is pressed.
Programs beeper On or Off for good read indications.
Modifies the volume of the beep emitted on a good read.
Modifies the pitch (frequency) of the beep emitted on a good read.
Specifies the high priority symbology by scanning its Hex value.
Specifies low priority symbology by scanning its Hex value.
Sets the time period scanner searches for high priority bar code after low priority.
Ensures all output data conforms to an edited sequence.
Programs scanner to output data in desired order, regardless of scan order.
Sends additional user-defined data before or after scanned bar code data.
Notes on building message strings and default settings.
Step-by-step guide to adding prefixes or suffixes to scanned data.
Allows changing scanner output by inserting characters into bar code data.
Steps to enter and save data formats for primary or alternate use.
Commands for sending characters or strings based on input message and criteria.
Deletes a single data format for one symbology.
Clears all data formats.
Enables or disables decoding of all allowable symbologies.
Sets valid reading length for symbologies to reduce misreads.
Enables or disables Codabar symbology decoding.
Transmits or does not transmit Codabar start/stop characters.
Programs scanner to read Codabar bar codes with specific modulo check characters.
Enables or disables Code 39 symbology decoding.
Transmits or does not transmit Code 39 start/stop characters.
Programs scanner to read Code 39 bar codes with specific check characters.
Enables or disables Interleaved 2 of 5 symbology decoding.
Programs scanner to read Interleaved 2 of 5 with or without check digit.
Enables or disables NEC 2 of 5 symbology decoding.
Programs scanner to read NEC 2 of 5 with or without check digit.
Enables or disables Code 93 symbology decoding.
Changes the minimum and maximum message length for Code 93.
Appends data from several Code 93 bar codes before transmitting.
Enables or disables Straight 2 of 5 Industrial symbology.
Changes message length for Straight 2 of 5 Industrial symbology.
Enables or disables Straight 2 of 5 IATA symbology.
Changes message length for Straight 2 of 5 IATA symbology.
Enables or disables Matrix 2 of 5 symbology decoding.
Changes message length for Matrix 2 of 5 symbology.
Enables or disables Code 11 symbology decoding.
Sets whether 1 or 2 check digits are required for Code 11.
Enables or disables Code 128 symbology decoding.
Standard for communicating critical blood information in a uniform manner.
Changes message length for Code 128 symbology.
Enables or disables GS1-128 symbology.
Changes message length for GS1-128 symbology.
Enables or disables Telepen symbology.
Configures Telepen output for AIM or Original Telepen.
Changes message length for Telepen symbology.
Enables or disables UPC-A symbology.
Specifies whether check digit is transmitted at the end of scanned UPC-A data.
Programs whether numeric system digit is transmitted at the beginning of scanned UPC-A data.
Enables or disables UPC-E0 symbology decoding.
Expands UPC-E code to 12 digit, UPC-A format.
Enables or disables EAN/JAN-13 symbology.
Converts UPC-A bar codes to 13 digit EAN-13 codes.
Enables or disables EAN/JAN-8 symbology.
Specifies whether check digit is transmitted at the end of scanned EAN/JAN-8 data.
Enables or disables MSI symbology.
Programs scanner to read MSI bar codes with specified type check characters.
Enables or disables GS1 DataBar Omnidirectional symbology.
Enables or disables GS1 DataBar Limited symbology.
Enables or disables GS1 DataBar Expanded symbology.
Changes message length for GS1 DataBar Expanded symbology.
Enables or disables Codablock A symbology.
Changes message length for Codablock A symbology.
Enables or disables Codablock F symbology.
Changes message length for Codablock F symbology.
Enables or disables PDF417 symbology.
Changes message length for PDF417 symbology.
Enables or disables MicroPDF417 symbology.
Changes message length for MicroPDF417 symbology.
Applies to both QR Code and Micro QR Code; enables or disables decoding.
Changes message length for QR Code.
Enables or disables Data Matrix symbology.
Changes message length for Data Matrix.
Enables or disables MaxiCode symbology.
Changes message length for MaxiCode symbology.
Enables or disables Aztec Code symbology.
Changes message length for Aztec Code.
Enables or disables Han Xin Code symbology.
Changes message length for Han Xin Code.
Lists and enables individual 2D postal code selections.
Default settings for China Post (Hong Kong 2 of 5) symbology.
Enables or disables China Post (Hong Kong 2 of 5) symbology.
Default settings for Korea Post symbology.
Enables or disables Korea Post symbology.
Imaging commands with modifiers take effect for single capture, reverting to defaults.
Describes how to combine multiple modifiers and commands in a sequence.
Command to capture an image, with various modifiers for image look.
Details modifiers for Image Snap: P-Imaging Style, B-Beeper, T-Wait for Trigger, L-LED State.
Command to transmit captured image data to the host.
Details modifiers for Image Ship: A-Infinity Filter.
Keyboard Function Code, Hex/ASCII Value, and Full ASCII CTRL+ relationships.
Table mapping ASCII/HEX values to PC/Mac keyboard and interface keys.
Temporarily enables transmission of Code I.D. before decoded symbology.
Outputs the decoder revision information.
Outputs the scan driver revision, which controls image capture.
Outputs current software revision, serial number, and other product information.
Scans bar codes, displays data in window, sends serial commands, receives responses.
Displays scanner programming and configuration data in a tree structure.
Provides image-related functions: capture, manipulate, and transfer images.
Defines conventions used for menu and query command descriptions.
Explains the syntax for menu commands including prefix, tag, subtag, and data.
Explains usage for Tag, SubTag, and Data fields in query commands.
Describes issuing multiple commands within one sequence using separators.
Table listing default settings for product configuration.
Table listing Plug and Play codes for interface programming.
Controls display of power indicator on base or Access Point.
Reboots scanner and relinks with base or Access Point.
Allows scanning bar codes while scanner is in base cradle.
Charges scanner without linking to base, retaining existing link.
Charges scanner and links it to the base.
Resets the base and waits for scanner to unlink and relink.
Resets the scanner and waits for base/Access Point to unlink and relink.
Stores bar code data when scanner is out of range, transmits automatically when back in range.
Stores bar code data regardless of range; transmits via base or Access Point.
Stores data, transmits, and retains it in scanner for multiple transmissions.
Pairs scanner with Bluetooth devices for keyboard input.
Technical specifications for Xenon 1900/1910 corded scanner, including dimensions, LED, aiming, and power.
Technical specifications for Xenon 1902/1912 cordless scanner, including dimensions, LED, aiming, and radio.
Technical specifications for Granit 1910i corded scanner, including dimensions, LED, aiming, and voltage.
Technical specifications for Granit 1911i cordless scanner, including dimensions, LED, aiming, and radio.
Technical specifications for CCB01-010BT charge base, including dimensions, voltage, radio, and temperature.
Technical specifications for CCB02-100BT industrial charge base, including dimensions, voltage, radio, and temperature.
Typical performance charts for Xenon B&W scanner across different symbologies and resolutions.
Pin assignments for 10 Pin RJ41 Modular Plug connecting scanner to base.
Pin assignments for 10 Pin RJ41 Modular Plug connecting scanner to base.
Services and upgrades must be performed by an authorized service center.
Guidelines for periodic checks to ensure dependable operation.
Instructions for cleaning scanner housing with soft cloth or tissue.
Instructions for cleaning scanner window to maintain performance.
Description of external plastic housing resistant to harsh chemicals.
Procedure for replacing the interface cable on a Xenon scanner.
Procedure for replacing the interface cable on a Granit scanner.
Procedure for replacing interface cable in CCB01-010BT and CCB02-100BT bases.
Check power connection, host power, and trigger function if aimer is not illuminated.
Guidelines for isolating base functionality problems.
Check symbol quality and enablement if scanner reads symbols poorly.
Check suffix programming if bar code data requires key entry.
Check terminal interface and symbology settings if data is read incorrectly.
Contact methods for installation or troubleshooting assistance.
Information on obtaining warranty or non-warranty service through service centers.
Warranty terms covering product defects in materials and workmanship.
Reference for AIM modifier characters and Honeywell IDs for symbologies.
Lists AIM and Honeywell IDs and modifiers for linear symbologies.
To Next Page
