Why my Hoover H-WASH 700 Washer does not work / start?
If your Hoover Washer isn't working or starting, ensure it's properly plugged into a working power socket and that the power is on. Test the wall socket with another appliance. Also, check that the door is correctly closed, and the required program is selected with the start button pressed. Make sure the washer isn't in pause or time delay mode.
Why is there water leaked on the floor near my Hoover Washing machine?
If you see water leaked on the floor near your Hoover Washing machine, it could be due to a leak from the seal between the tap, supply hose, and fill valve; in this case, replace it and correctly tighten the hose connections. Also, make sure the front filter is correctly closed.
Why is my Hoover Washer leaking water?
If you notice water leaking on the floor near your Hoover Washer, it could be due to a leak from the seal between the tap, supply hose, and fill valve; in this case, replace it and tighten the hose connections correctly. Also, make sure the front filter is correctly closed.
What to do if my Hoover H-WASH 700 does not spin?
If your Hoover Washer is not spinning, try these steps: First, remove the load, de-tangle it, reload it, and restart the spin program. If water hasn't completely drained, wait a few minutes. Also, some models have a "no spin" function, so ensure it's not selected. Check the selected options and their effect on the spin cycle. Finally, using too much detergent can impede the spin cycle, so ensure you're using the correct amount.
Why is my Hoover H-WASH 700 Washer making strong vibrations / noises during the spin cycle?
To address strong vibrations or noises during the spin cycle of your Hoover Washer, first, ensure the appliance is fully leveled by adjusting the feet. Next, verify that all transport screws, rubber bungs, and spacer tubes have been removed. Finally, check the drum for any foreign objects like coins or buttons.
What to do if my Hoover Washer shows E7 error / 7 flashes?
If your Hoover Washer displays 'E7' or the LEDs flash 7 times, ensure the door is correctly closed and that no clothes are preventing it from fully closing. If the door is locked, turn off and unplug the washing machine, wait 2-3 minutes, and then reopen the door.
How to fix Hoover H-WASH 700 Washer E2 error / 2 flashes?
If your Hoover Washer displays 'E2' or the LEDs flash 2 times, make sure the water supply tap is open and that the water supply hose isn’t bent, kinked, or trapped. Ensure the drain pipe is at the proper height. Close the water supply tap, unscrew the filler hose, and check that the “anti-sand” filter is clean and not blocked. Also, check that the filter is not clogged and that there are no foreign bodies inside the filter compartment.
What to do if my Hoover H-WASH 700 Washer shows E4 error / 4 flashes?
If your Hoover Washer displays 'E4' or the LEDs flash 4 times, ensure the correct amount of detergent is being used and that the detergent is designed for use in a washing machine.
How to fix Hoover Washer error E7?
If your Hoover Washer displays error code E7 or flashes the LEDs 7 times, make sure that the door is correctly closed and that no clothing is preventing it from closing fully. If the door is locked, try turning off and unplugging the washing machine from the electrical supply socket, wait 2-3 minutes and then try reopening the door.
Why is my Hoover Washer vibrating so much?
If you're experiencing strong vibrations or noises during the spin cycle of your Hoover Washer, it might not be fully leveled. Adjust the feet as indicated in the relevant section of the manual. Also, ensure that the transport screws, rubber bungs, and spacer tubes have been removed. Finally, check the drum for any foreign objects like coins, hinges, or buttons.
General| Loading type | Front-load |
|---|---|
| Colour | White |
| Built-in display | Yes |
| Drum material | Stainless steel |
| Washing class | A |
| Delayed start timer | Yes |
| Delayed start | 24 hours |
| Width | 600 mm |
| Height | 850 mm |
To Next Page
