Index
3
Numerics
1.5M REF IN, 2-7
2M REF IN, 2-7
52/155 Mb/s DATA IN, 2-7
52/155 Mb/s DATA OUT, 2-7
64k REF IN, 2-7
A
Accessories
Connection, 2-11
Alternative External MTS Clock, 3-64
Assistance, 1-3
Australian EMC Regulations
Compliance with, 1-10
C
Cabinet Cleaning, 1-8
Certification, 1-3
Cleaning, 1-8
Cabinet, 1-8
Optical Connectors, 1-8
CLOCK TRIGGER, 2-8
Compliance, Statement of, 1-10
Connecting
Accessories, 2-11
ESD Precautions Necessary, 2-6
To the Network, 2-6
To the Power Supply, 2-4
Connectors
Electrical Interface, 2-6
Optical Interface, 2-9
D
DEMUX 2 Mb/s 75 ohm Connector, 2-7
DEMUX DS1 100 ohm Connector, 2-7
Dimensions and Weight, 1-5
DS1 100 ohm, 2Mb/s 120 ohm IN Connec-
tor, 2-7
DS1 100 ohm, 2Mb/s 120 ohm OUT, 2-7
DS3, 2Mb/s, 34Mb/s 75 ohm IN Connec-
tor, 2-6
DS3, 2Mb/s, 34Mb/s 75 ohm OUT Con-
nector, 2-6
E
Electrical Interface Connectors, 2-6
Electromagnetic Compatibility, 1-11
Electrostatic Discharge, 1-11
Environment
Operating, 2-2
Storage and Shipment, 1-4
ESD Precautions
For the Service Engineer, 2-6, 2-14
External 2Mb/s Mux/Demux, 3-44
External MTS Clock, 3-59
F
Fuse Replacement, 2-3
Fuses, 2-3
H
HANDSET Connector, 2-11
Hewlett-Packard Interface Bus, 2-12
HP-IB, 2-12
Address Selection, 2-13
Connections, 2-13
HP-IB Address, 2-13
HP-IB Connection, 2-12
I
Inspection, Initial, 2-1
Instruments Covered By Manual, 1-4
Internal SDH Transmitter Clock, 3-58
J
Jitt. Amp. PDH Tx/Rx, 89
Jitt. Amp. SDH Tx/Rx, 101
L
Laser apertures
Location, 2-10
LID Connector, 2-11
Lifting/Carrying the Instrument, 1-6
Location of Laser Apertures, 2-10
M
Maintenance by the Operator, 1-8
MUX 2 Mb/s 75 ohm Connector, 2-7
MUX Connector, 2-7
MUX DS1 100 ohm Connector, 2-7
N
Noise Declaration (German), 1-10
O
Operators Maintenance, 1-8
Optical Connector Cleaning, 1-8
OPTICAL IN Connector, 2-10
Optical Interface Connectors, 2-9
OPTICAL OUT Connector, 2-10
P
PDH Frequency Measurement and Looped
Clock, 3-54, 3-57
PDH Receiver Equalization, 3-32, 3-75
PDH Tx/Rx Jit. Amp., 89
Performance Test Record, 121, 131
Power Cord, 2-5
Power Requirements, 2-3
Power Supply Connection, 2-4
Precautions
ESD when connecting, 2-6
Precautions for the Service Engineer, 2-14
Preparation for Use, 2-3
Printer HP-IB, RS232, PARALLEL
ONLY Connector, 2-11
R
Recall Default Settings, 3-4
RECEIVER 2,8,34,140 IN, 2-6
Recommended Test Equipment, 3-5
REF OUT, 2-7
Remote Control HP-IB, RS232, 10 BASE
-T Connector, 2-11
Repackaging, 1-4
Responsibilities of the Customer, 1-2
Restricted Rights Legend, 1-3
S
Safety Information, 1-6
Safety Precautions
For the Operator, 1-6
For the Service Engineer, 2-14
Safety Symbols, 1-7
SDH Frequency Offsets, 3-64, 3-65
SDH Tx/Rx Jitt. Amp., 101
Self Test, 3-5
Serial Number Plate, 1-4
Shipping Container Inspection, 2-1
SPDH Receiver Monitor Levels, 3-39, 3-
78
Statement of Compliance, 1-10
STM-1 Transmitter Output Waveshape, 3-
66, 3-70
To Next Page
Loading...
Need help?
General
