HP 9000 rp4440 - Figure 3-3 Installing Processor on Extender Board

To Next Page

To Previous Page

Chapter 3

Upgrade Procedures for 1.1 GHz mx2 Dual Processor Modules (A9730A)

Introduction

Figure 3-3 Installing Processor on Extender Board

Step 7. Use a long flat blade screwdriver to tighten screws 5 and 6 shown in Figure 3-3, “Installing

Processor on Extender Board.”

Align pins on

heatsink

with slots

Power

cable protected by plastic

sleeve

slots*

*slots shown are at

CPU socket #1 for

clarity.

Processor shown is

being mounted on

socket #0 per CPU load

order.

Torx-T15

Use supplied

wrench for

tightening

shoulder screws

and thumbscrews

2.5MM Allen

Tightening sequence for 4-shoulder

screws is:

1,2,3,4,5,6

DO NOT OVERTIGHTEN!

Main Page

Table of Contents3
Overview-Server Upgrade7
Overview7
Time Required7
Upgrade Tasks7
Figure 1-1 Hp 9000 Rp4440 Server7
Common Procedures9
Accessing a Rack Mounted Server9
Extend the Server from the Rack9
Insert the Server into the Rack10
Accessing a Pedestal Mounted Server10
Figure 1-2 Accessing 25MM Torx Screws10
Figure 1-3 Pedestal Mounted Hp Server11
Front Bezel12
Figure 1-4 Removing and Installing the Front Bezel12
Removing the Front Bezel13
Installing the Front Bezel13
Front and Top Covers14
Figure 1-5 Removing and Installing the14
Removing the Front Cover15
Installing the Front Cover15
Figure 1-6 Removing and Installing the Top Cover16
Removing the Top Cover17
Installing the Top Cover17
Processor Extender Board18
Removing the Processor Extender Board18
Figure 1-7 Processor Extender Board19
Installing the Processor Extender Board20
Hot-Swap Chassis Fan Unit20
Figure 1-8 Hot-Swap I/O Chassis Fans Removal and Replacement21
Upgrade Procedures for 1.3 Ghz (A7158A) or 1.5 Ghz (A7159A) Processors23
Introduction24
Required Tools24
Back up Your System24
Installing Processors25
Removing a Processor26
Installing a Processor26
Figure 2-1 Processor Cable Placed Correctly28
Figure 2-2 Processor Cable Placed Incorrectly28
Figure 2-3 Installing Processor on Extender Board30
Enabling the Onboard VGA31
Figure 2-4 Processor Extender Board Switches31
Figure 2-5 IO Baseboard Select Switches32
Installing Server Components33
Verification of Upgrade Installation33
Figure 2-6 VGA Port Cover Panel33
Upgrade Procedures for 1.1 Ghz Mx2 Dual Processor Modules (A9730A)35
Introduction35
Required Tools35
Back up Your System35
Installing Processors36
Removing a Processor37
Installing a Processor37
Figure 3-1 Processor Cable Placed Correctly39
Figure 3-2 Processor Cable Placed Incorrectly39
Figure 3-3 Installing Processor on Extender Board42
Figure 3-4 Processor Extender Board Switches43
Enabling the Onboard VGA44
Figure 3-5 IO Baseboard Select Switches44
Installing Server Components45
Verification of Upgrade Installation45
Figure 3-6 VGA Port Cover Panel45
Upgrade Procedures for 1.5 Ghz (A9731AX) or 1.6 Ghz (A9732AX or A9733AX) Dual Processors47
Introduction48
Required Tools48
Back up Your System48
Installing Processors49
Removing a Processor50
Installing a Processor50
Figure 4-1 Processor Cable Placed Correctly52
Figure 4-2 Processor Cable Placed Incorrectly52
Figure 4-3 Installing Processor on Extender Board54
Enabling the Onboard VGA55
Figure 4-4 Processor Extender Board Switches55
Figure 4-5 IO Baseboard Select Switches56
Installing Server Components57
Verification of Upgrade Installation57
Figure 4-6 VGA Port Cover Panel57

HP 9000 rp4440 - Figure 3-3 Installing Processor on Extender Board

Table of Contents

Other manuals for HP 9000 rp4440

Related product manuals