To Next PageTo Next Page
Need help?Do you have a question about the HP ProLiant BL460c G6 and is the answer not in the manual?
General| Tcase | 76 °C |
|---|---|
| Bus type | QPI |
| Stepping | D0 |
| FSB Parity | No |
| Processor code | SLBF6 |
| Processor cache | 8 MB |
| Processor cores | 4 |
| Processor model | E5540 |
| System bus rate | 5.86 GT/s |
| Processor series | Intel Xeon 5500 Series |
| Processor socket | Socket B (LGA 1366) |
| Processor threads | 8 |
| Processor codename | Nehalem EP |
| Processing Die size | 263 mm² |
| Processor frequency | 2.53 GHz |
| Processor cache type | Smart Cache |
| Processor lithography | 45 nm |
| Processor system type | DP |
| Processor manufacturer | Intel |
| Processor package size | 42.5 x 45 mm |
| Processor front side bus | - MHz |
| Processor boost frequency | 2.8 GHz |
| Processor operating modes | 64-bit |
| ECC supported by processor | Yes |
| Thermal Design Power (TDP) | 80 W |
| Number of processors installed | 1 |
| CPU multiplier (bus/core ratio) | 19 |
| Maximum number of SMP processors | 2 |
| Memory types supported by processor | DDR3-SDRAM |
| Number of Processing Die Transistors | 731 M |
| Memory channels supported by processor | Triple |
| Memory clock speeds supported by processor | 800, 1066 MHz |
| Memory bandwidth supported by processor (max) | 25.6 GB/s |
| Maximum internal memory supported by processor | 144 GB |
| HDD size | - \ |
| HDD interface | Serial ATA, Serial Attached SCSI (SAS) |
| Total storage capacity | 0 GB |
| Maximum storage capacity | 1 TB |
| Number of HDDs installed | 0 |
| Memory slots | 12x DIMM |
| Internal memory | 6 GB |
| Memory clock speed | 1333 MHz |
| Maximum internal memory | 192 GB |
| Memory layout (slots x size) | 3 x 2 GB |
| Cabling technology | 10/100/1000Base-T(X) |
| USB 2.0 ports quantity | - |
| Chassis type | Blade |
| Processor ARK ID | 37104 |
| Intel® Turbo Boost Technology | 1.0 |
Weight and Dimensions| Depth | 56 mm |
|---|---|
| Width | 182 mm |
| Height | 510 mm |
| Weight | 6440 g |
Identifies and describes the various components located on the server blade's system board.
Instructions on how to power on the server blade using different methods.
Procedures for safely powering down the server blade for maintenance or upgrades.
Step-by-step guide on how to safely remove the server blade from the enclosure.
Instructions for installing SAS or SATA hard drives into the server blade.
Detailed steps for installing a processor, including safety warnings and alignment.
Overview of memory types, configurations, and installation guidelines.
Steps for installing and enabling the Trusted Platform Module (TPM) on the server.
Details on iLO 2 for remote server management, health, and troubleshooting.
Overview of diagnostic tools including HP Insight Diagnostics and IML.
Essential preparatory steps and warnings before troubleshooting system components.
Highlights safety warnings, symbols, and precautions for equipment handling.
Guides on collecting relevant information about server symptoms before troubleshooting.
Steps to prepare the server environment and gather necessary tools for diagnosis.
Guidelines for troubleshooting steps involving processors, including warnings.
Procedure for reducing the server to its minimum configuration for troubleshooting.
The initial flowchart to guide the diagnostic process for server issues.
A generic approach to troubleshooting when problems are not server-specific.
Flowchart for diagnosing issues related to the server blade not powering on.
Flowchart for troubleshooting when the server fails to complete POST.
Flowchart for diagnosing issues related to the server's operating system boot process.
Flowchart for identifying server faults based on system indicators and alerts.
Reference for POST error messages and beep codes for troubleshooting.
Instructions for replacing the server blade's real-time clock battery.
Precautions to prevent damage to system components from static electricity.
Methods and guidelines for proper grounding when handling sensitive parts.
