HP Z400 User Manual

Table 4-1 Computer Setup (F10) Utility menu descriptions (continued)
Heading Option Description
Advanced
2
Power-On
Options
Lets you set the following:
●
POST Messages—Enables or disables the splash screen during POST.
●
F9 Prompt (Displayed or Hidden)—Selecting Displayed displays the
F9=Boot Menu during POST. Selecting Hidden prevents the text from
being displayed. However, pressing F9 still accesses the boot menu.
●
F10 Prompt (Displayed or Hidden)—Selecting Displayed displays
F10=Setup during POST. Selecting Hidden prevents the text from being
displayed, but pressing F10 still accesses the Setup screen.
●
F12 Prompt (Displayed or Hidden)—Selecting Displayed displays
F12=Network Service Boot during POST. Selecting Hidden prevents
the text from being displayed but pressing F12 still forces the workstation to
attempt booting from the network.
●
Option ROM
1
prompt (Enable or Disable)—Enabling this feature causes the
workstation to display a message before loading options ROMs.
●
Remote Wakeup Boot Source—Enables you to set the remote wakeup boot
source as:
◦
Local Hard Drive
◦
Remote Server
●
After Power Loss (On, Off, Previous State)—Enabling this option directs the
previous state to be the default.
●
POST Delay (in seconds) (5, 10, 15, 20, None)—Adds a specified delay
to the POST process. This delay is sometimes needed for hard disk drives
on some expansion cards that spin up slowly (so slowly that they are not
ready to start by the time POST is finished). The POST delay also gives you
time to select F10 to enter the Computer Setup (F10) Utility.
BIOS Power-On Lets you disable or specify a weekday and time for BIOS power-on.
Processors Enables/disables these options:
●
Hyper-Threading—Provides processor parallelization such that the
operating system treats one processor as two.
●
Active Cores (1,2, or All Cores)—Selects a single core, or multiple cores
per socket. (Not available on some configurations.)
●
Limit CPUID Maximum Value to 3 (Enable or Disable)—Sets the number of
allowable CPU IDs.
Onboard Devices Lets you set resources (IRQ, DMA, I/O Rate) or disable onboard system devices
such as serial port and diskette controller. Operating system parameters
generally override Onboard Devices settings.
PCI VGA
Configuration
Configures which expansion slots are used for graphics cards. In multi-graphics
card configurations, this option designates one graphics card as primary and
the other card as secondary.
ENWW
The Computer Setup (F10) Utility
41

HP Z400 Specifications

General

Bus type	QPI
Processor cache	4 MB
Processor cores	2
Processor model	W3503
System bus rate	4.8 GT/s
Processor socket	-
Processor frequency	2.4 GHz
Processor cache type	Smart Cache
Processor lithography	45 nm
Processor manufacturer	Intel
PCI Express slots version	2.0
Processor operating modes	64-bit
ECC supported by processor	Yes
Thermal Design Power (TDP)	130 W
Number of processors installed	1
Memory types supported by processor	DDR3-SDRAM
Memory clock speeds supported by processor	800, 1066 MHz
Memory bandwidth supported by processor (max)	25.6 GB/s
Maximum internal memory supported by processor	24 GB
Audio system	Realtek ALC262
Product type	Workstation
Motherboard chipset	Intel® X58 Express
Memory slots	6x DIMM
Internal memory	4 GB
Memory channels	Triple-channel
Memory clock speed	1066 MHz
Memory layout (slots x size)	- GB
Graphics card	Quadro 600
Networking features	Gigabit Ethernet (10/100/1000)
Graphics card family	NVIDIA
HDD speed	- RPM
RAID levels	0, 1, 5, 10
HDD capacity	500 GB
HDD interface	SATA II
Storage media	HDD
Display included	No
USB 2.0 ports quantity	8
Parallel ports quantity	0
Chassis type	Minitower
Country of origin	China
Number of 5.25\" bays	3
Operating system installed	Windows 7 Professional
Operating system architecture	32-bit
Power supply	475 W
Processor ARK ID	40800
Processor package size	42.5 x 45 mm
Supported instruction sets	SSE4.2

Weight and Dimensions

Depth	455.3 mm
Width	167.9 mm
Height	450.2 mm
Weight	13500 g