Huawei OptiX RTN 950A - Fixing the E1 Panel; Installing PGND Cables on the E1 Panel

49 pages

To Next Page

To Previous Page

Fixing the E1 Panel

Installing PGND Cables on the E1 Panel

To the ground point on the column of

the cabinet or the indoor ground bar

Main Page

Installation Process3
Commissioning Process4
Precautions5
Electrostatic Discharge5
Power Supply5
Binding Cables5
Instructions and Precautions for Handling Boards6
Instructions and Precautions for Handling Power Cable Terminals7
Precautions for Handling the Toggle Lever Switch8
Position and Description of the Toggle Lever Switch8
Turning on the Switch8
Turning off the Switch8
Precautions for Handling IDU-Side if Cables9
Precautions for Handling ODU-Side if Cables9
Precautions for Installing if Cables (Dual-Channel if Board)10
Precautions for Removing if Cables10
Precautions for Handling if Boards11
Tools for Installation12
Introduction to the RTN 950A Equipment13
Ports13
Installation Holes on both Sides of the Chassis13
Installing the RTN 950A14
Installing the Chassis in the 19-Inch Cabinet14
Fixing Floating Nuts14
Removing Screws14
Installing the Chassis in the Cabinet15
Installing PGND Cables15
Installing the Chassis in the ETSI Cabinet15
Installing the Chassis in the 23-Inch Cabinet16
Wall-Mounting the Chassis17
Removing Mounting Ears17
Marking and Drilling Holes17
Desk-Mounting the Chassis20
Installing Plastic Feet20
Optional: Installing the E1 Panel20
Fixing the E1 Panel21
Installing PGND Cables on the E1 Panel21
Optional: Installing Transfer Brackets for if Jumpers22
Installing if Connectors22
Installing Two if Connectors22
Installing Transfer Brackets for if Jumpers23
Installing Transfer Brackets for if Jumpers in 19-Inch Cabinets23
Installing Transfer Brackets for if Jumpers in ETSI Cabinets23
Installing Transfer Brackets for if Jumpers on Walls24
Installing Boards25
Installing IDU Cables25
Installing Power Cables26
Installing E1 Cables27
Optional: Connecting E1 Cables to the External Equipment27
Optional: Connecting E1 Cables to the E1 Panel28
Optional: Connecting E1 Cables to the TCU6 Board28
Installing Ethernet Service Cables29
Installing XPIC Cables29
Installing if Jumpers30
Optional: Connecting the if Jumper Directly to the if Cable30
Installation Effectiveness in the 19-Inch Cabinet31
Installation Effectiveness in the ETSI Cabinet31
Installation Effectiveness on the Wall32
Installing Fibers33
Installing STM-1E Cables34
Installing NM Cables34
Installing NM Cables (for a Gateway NE)34
Installing Orderwire Phone Cables35
Installing External Clock Cables36
Assembling External Clock Cables Based on the Pin Assignment36
Installing External Clock/Time Cables for the IDU36
Installing Asynchronous and Synchronous Data Cables37
Installing Synchronous and Asynchronous Data Cables for the IDU37
Installing External Alarm Cables38
Installing External Alarm Cables for the IDU38
Cable Layout Effectiveness39
Cable Connections39
Powering on the Equipment40
Status Description of Indicators40
Configuring NE Data (Using the USB Flash Drive)41
Insert a USB Flash Drive41
Configuring NE Data (by Using the Web LCT)42
Configuring NE Data (by Using the Hand-Held Tool)42
Aligning Antennas43
Aligning Single-Polarized Antennas43
Aligning Dual-Polarized Antennas44
Checking the Radio Link Status45
Checking the Installation46
Connecting Cables to a Power Cable Connector47
Obtaining Tools, Cables, and a Power Cable Connector47
Peeling Cables47
Connecting Cables to the Power Cable Connector48

Huawei OptiX RTN 950A - Fixing the E1 Panel; Installing PGND Cables on the E1 Panel

Table of Contents

Related product manuals