Why is my Huawei Inverter showing an abnormal grid voltage?
This alarm may occur accidentally if the power grid is temporarily abnormal. The Huawei SUN2000 automatically recovers after detecting that the power grid becomes normal. This is due to the grid voltage being below the specified lower threshold.
How to fix high DC input voltage on Huawei SUN2000-33KTL-A Inverter?
This issue occurs when the PV array is not properly configured. Reduce the number of PV modules connected in series to PV strings 1 and 2 until the open-circuit voltage is less than or equal to the maximum inverter input voltage. After the PV array configuration is corrected, the Huawei SUN2000 alarm disappears.
What causes abnormal grounding in Huawei Inverter?
This issue may be due to the neutral wire or PGND cable not properly connected to the inverter, or the Huawei SUN2000 output side does not connect to an isolation transformer when the PV string output is grounded. Check that the neutral wire or PGND cable properly connects to the inverter. If the PV string output is grounded, check that the SUN2000 output side connects to an isolation transformer.
What does abnormal grid frequency mean on a Huawei Inverter?
If the alarm occurs accidentally, the power grid may be abnormal temporarily. The Huawei SUN2000 automatically recovers after detecting that the power grid becomes normal. This happens because the actual grid frequency is higher than the standard requirement for the local power grid.
How do I troubleshoot low insulation resistance on a Huawei SUN2000-33KTL-A?
Check the impedance between the PV string and the PGND cable. If a short circuit occurs, rectify the fault. If you are sure that the impedance is less than the default value in a cloudy or rainy environment, log in to the SUN2000 app, SmartLogger, or NMS and set Insulation resistance protection. A short circuit occurs between the PV string and the PGND cable.
What does abnormal DC circuit mean for Huawei SUN2000-33KTL-A?
The Huawei SUN2000 detects its external working conditions in real time. After the fault is rectified, the SUN2000 automatically recovers. This issue occurs when the SUN2000 input is disconnected accidentally, or the PV string output power changes sharply because the PV string is shielded from sunlight.
What causes a DC arc fault in my Huawei SUN2000-33KTL-A?
Check whether the PV string cable is in poor contact or with open circuits. If yes, reconnect the cable. The PV string cable is in poor contact or with open circuits.
Why is my Huawei SUN2000-33KTL-A showing a cabinet overtemperature warning?
Check the ventilation and ambient temperature of the Huawei SUN2000 installation position. If the ventilation is poor or the ambient temperature exceeds the upper threshold, improve the ventilation and heat dissipation. If the ventilation and ambient temperature both meet requirements, contact Huawei technical support. This issue occurs when the SUN2000 is installed in a place with poor ventilation, the ambient temperature exceeds the upper threshold, or the internal fan works abnormally.
What to do if string 1-8 reversed on Huawei Inverter?
Check whether the PV string is reversely connected to the Huawei SUN2000. If yes, wait until the solar irradiance declines at night and the PV string current reduces to below 0.5 A. Then, turn off the two DC switches and correct the PV string connection. Check whether the number of PV modules connected in series to the SUN2000 is small. If yes, increase the number. The PV string is reversely connected or only a few PV modules are connected in series to the PV string, and therefore the end voltage is lower than that of other PV strings.
How to resolve AFCI self-check failure on Huawei Inverter?
Turn off the AC output switch and DC input switch. Then turn on the AC output switch and DC input switch after 5 minutes. If the fault persists, contact Huawei technical support. Disable the AFCI function if you are sure not to use it. AFCI check fails.
General| Model | SUN2000-33KTL-A |
|---|---|
| Type | String Inverter |
| Rated Output Power | 33 kW |
| Max. DC Input Voltage | 1100 V |
| Input Voltage Range | 200 V - 1000 V |
| Number of MPPT Trackers | 2 |
| Max. Apparent AC Power | 33 kVA |
| Rated AC Power | 33 kW |
| Rated AC Voltage | 400 V |
| Rated Grid Voltage | 400 V |
| Rated Grid Frequency | 50 Hz / 60 Hz |
| Max Efficiency | 98.6% |
| Protection Level | IP65 |
| Operating Temperature Range | -25°C to 60°C |
| Cooling Method | Natural Cooling |
To Next Page
