What to do if my Huawei SUN2000-60KTL-M0 shows a Grid Loss error?
If the Huawei Inverter displays a 'Grid Loss' error, it could be due to a power outage in the grid or a disconnection in the AC circuit. First, verify if there is a power outage in your area; the alarm should clear automatically once the grid recovers. If the grid is stable, check that the AC power cable is properly connected and the AC switch is turned ON.
Why does my Huawei Inverter show a Grid Overvoltage error?
A 'Grid Overvoltage' error on your Huawei Inverter indicates that the grid voltage is too high. First, check if the grid connection voltage exceeds the upper threshold. If it does, contact your local power operator. If you have confirmation from the power operator and their consent, you may need to modify the overvoltage protection threshold. Also, ensure the peak grid voltage does not exceed the upper threshold.
What causes a Grid Undervoltage error on a Huawei Inverter?
A 'Grid Undervoltage' error on your Huawei Inverter means the grid voltage is too low. If the alarm is temporary, it might be due to a temporary grid issue, and the SUN2000 should recover automatically. If it happens frequently, check if the grid voltage is within the acceptable range; if not, contact your local power operator. If the voltage is within range, you might need to adjust the undervoltage protection threshold with the power operator's approval. Also, check the AC circuit breaker and AC output power cable if the issue persists.
How to fix a High String Input Voltage error on a Huawei Inverter?
If your Huawei Inverter is showing a 'High String Input Voltage' error, it means the PV array is configured incorrectly. Too many PV modules are connected in series, causing the PV string's open-circuit voltage to exceed the SUN2000's maximum operating voltage. Reduce the number of PV modules connected in series until the PV string's open-circuit voltage is within the acceptable range. The alarm should then stop.
What does Low Insulation Resistance mean on my Huawei Inverter?
If your Huawei Inverter shows a 'Low Insulation Resistance' error, it could be due to a short circuit between the PV string and the PE cable, or the PV string may have been exposed to moisture, reducing the cable's insulation. Check the impedance between the PV string and the PE cable for any short circuits and correct them. Also, ensure the PE cable is correctly connected. If the impedance is lower than expected in a cloudy or rainy environment, you can try resetting the insulation resistance protection.
Why is my Huawei SUN2000-60KTL-M0 showing an Abnormal Grounding error?
If the Huawei Inverter displays 'Abnormal Grounding', it could be due to a disconnected PE cable or the absence of an isolation transformer when the PV string output is grounded. Verify that the PE cable is properly connected to the SUN2000. If the PV string output is grounded, ensure that the SUN2000 output side is connected to an isolation transformer.
What causes an Output Overcurrent error on a Huawei SUN2000-60KTL-M0?
If your Huawei Inverter reports 'Output Overcurrent', it's likely because the grid voltage has dropped significantly or the grid is short-circuited, causing the inverter's output current to exceed the limit. The inverter should automatically recover once the fault is resolved. If the alarm occurs frequently, check for any short circuits in the output. If the issue persists, contact Huawei technical support.
How to resolve a Cabinet Overtemperature error on a Huawei SUN2000-60KTL-M0 Inverter?
If your Huawei Inverter shows a 'Cabinet Overtemperature' error, it could be due to poor ventilation, high ambient temperature, or a malfunction in the SUN2000. Check the ventilation and ambient temperature around the installation. If ventilation is poor or the temperature is too high, improve the airflow and reduce the temperature. If those are within range, contact Huawei technical support.
What to do if Huawei SUN2000-60KTL-M0 Inverter displays String Reverse Connect?
If you see a 'String Reverse Connect' error on your Huawei SUN2000 Inverter, the PV string is likely connected in reverse. Check the connection of the PV string to the SUN2000 and correct it.
Why does my Huawei Inverter show Grid Overfrequency?
If the Huawei Inverter displays 'Grid Overfrequency', it means the grid frequency is higher than the local power grid standard. If it's a one-time occurrence, it might be a temporary grid issue, and the SUN2000 should recover automatically. If it happens often, check if the grid frequency is within the acceptable range. If not, contact your local power operator. If it is within range, you may need to adjust the overfrequency protection threshold with their consent.
Provides general safety guidelines and precautions for equipment operation.
Details the qualifications and training required for personnel.
Covers crucial safety aspects related to electrical connections and grounding.
Provides guidance on maintaining and replacing components safely.
Specifies environmental and positional requirements for installing the inverter.
Guides the process of installing the mounting bracket.
Covers the context and precautions for physically installing the solar inverter.
Lists essential safety precautions before making electrical connections.
Explains the procedure for connecting the protective earthing (PE) cable.
Guides the connection of tracking system and AC output power cables.
Provides detailed instructions and precautions for connecting DC input power cables.
Outlines advanced operations for users with higher access levels.
Explains how to configure grid-related parameters for the inverter.
Guides on setting various protection parameters for the inverter.
Details how to power off the inverter for troubleshooting or replacement.
Provides information on common alarms, their causes, and troubleshooting steps.
To Next Page
General