What to do if Hunter Douglas Window Blinds will not snap into the installation brackets?
If your Hunter Douglas window blinds shading will not snap into the installation brackets, check that the installation brackets are aligned and level and that the locking tab on the installation bracket slides over the headrail.
Why are my Hunter Douglas Window Blinds hard to raise or lower, or the bottom rail does not stop at the top limit?
If your Hunter Douglas window blinds are hard to raise or lower, or the bottom rail doesn't stop at the top limit, check the adjustment position of the Headrail Limit Stop limit stops. The top illustration shows the correct adjustment. To correct this, the limit to Adjust stop should be adjusted one step up by pulling back on the rear of the limit stop to adjust its position. Ensure both limit stops are adjusted to the same position to prevent skewing.
How to fix Hunter Douglas Window Blinds that raise or lower unevenly?
If your Hunter Douglas window blinds raise or lower unevenly, or the bottom rail is uneven when fully raised, check if the window is square by measuring the diagonals and ensure the installation brackets are level. Use shims to level if necessary.
What to do if the universal cord tensioner grabs onto the cord upon operation of Hunter Douglas EasyRise Window Blinds?
If your Hunter Douglas EasyRise window blinds' universal cord tensioner grabs the cord during operation, ensure the universal cord tensioner is properly mounted. Reinstall if needed.
How to replace batteries in Hunter Douglas Indoor Furnishing battery wand?
To replace the batteries in your Hunter Douglas Indoor Furnishing battery wand, squeeze the cap latch to release and remove the cap. Install the new batteries following the instructions on the battery wand label. Then, press the cap back on until it latches. Hunter Douglas recommends using AA alkaline batteries for battery-powered shadings.
Why Hunter Douglas Silhouette Indoor Furnishing shading raises from the sill when the vanes are closed?
A small gap between the sill and the bottom of your Hunter Douglas Indoor Furnishing shading is normal when the vanes are closed, this allows the bottom rail to move freely. However, if the gap is excessive or changes over time, adjustments may be needed.
What to do if Hunter Douglas Silhouette Indoor Furnishing shading is hard to raise or lower?
If your Hunter Douglas shading is difficult to raise or lower, or it's stuck, here's what you can do: First, if it's an inside mount, ensure it's installed correctly and there's enough space between the shading's ends and the window frame. For LiteRise, close the vanes by pressing down on the handle's front before raising. If needed, pull the shading away from the window to fully close the vanes. For EasyRise, check the universal cord tensioner is mounted correctly; pull down the spring to release tension and move the tensioner to the cord loop's bottom, then properly mount it. Also, verify the installation brackets are level and use shims to adjust if necessary.
Why is my Hunter Douglas Silhouette shading raising unevenly?
If your Hunter Douglas shading raises unevenly or the bottom rail is uneven when fully raised, check the following: First, verify that the window is square by measuring the diagonals. Next, ensure the installation brackets are level and use shims to correct any unevenness. Then, adjust the bottom rail weight, which isn't applicable for LiteRise shadings. For LiteRise, maintain a level bottom rail while raising the shading to prevent fabric skewing.
Why does my Hunter Douglas Silhouette Indoor Furnishing shading not raise or lower completely?
If your Hunter Douglas Indoor Furnishing shading isn't raising or lowering fully, check that the fabric isn't catching on any brackets or window components. You may also need to adjust the upper and/or lower bottom rail travel limits.
What to do if Hunter Douglas Silhouette shading will not fit into the installation brackets?
If your Hunter Douglas Indoor Furnishing shading doesn't fit into the installation brackets, first check if a battery wand is interfering. Ensure the brackets are level and aligned, adjusting or shimming if necessary. Make sure mounting screw heads are flush against the brackets and the headrail is fully inserted, allowing the locking lever to slide over it.
General| Material | Fabric |
|---|---|
| Light Control | Adjustable |
| UV Protection | Yes |
| Operating Systems | PowerView Motorization |
| Available Widths | Up to 144 inches |
| Privacy | Adjustable |
| Vane Sizes | 2 inches |
| Customization | Yes |
To Next Page
