How to make Hunter Douglas Applause Indoor Furnishing shade stay in the raised position?
To lock the Hunter Douglas Indoor Furnishing shade in the raised position (or anywhere along the path to the fully raised position), engage the cordlock by pulling the cord toward the outside of the shade.
Why does my Hunter Douglas Applause Indoor Furnishing shade raise unevenly?
If your Hunter Douglas Indoor Furnishing shade raises or lowers unevenly, or the bottom rail is uneven when fully raised, try the following: * Lower the shade completely to allow it to self-correct, pulling the cord loop slowly to prevent further skewing. * Ensure the headrail and installation brackets are level and aligned, using shims if necessary. * For Duolite and Top-Down/Bottom-Up Shades: Lower each rail completely to allow them to self-correct and adjust the bottom rail.
How to install Hunter Douglas Applause Indoor Furnishing if the shade won't fit the brackets?
To address a Hunter Douglas Indoor Furnishing shade that won't fit into the installation brackets: * Confirm the installation brackets are level and properly aligned. * If needed, use shims to level the headrail via the installation brackets. * Ensure screw heads are flush against the installation bracket. * Verify the headrail is fully inserted into the installation brackets.
How to fix Hunter Douglas Applause Indoor Furnishing shade that is hard to raise or lower?
If your Hunter Douglas Indoor Furnishing shade is hard to raise or lower, first, ensure the fabric isn't caught between the installation bracket and the headrail. Next, verify that the headrail and installation brackets are level; if needed, level the headrail by shimming the installation brackets. Finally, check if the window is square by measuring the diagonals. If it's more than 1/4" out of square, the TrimKit won't function correctly, causing the shade to bind if too narrow or the end caps to fall out if too wide.
What to do if Hunter Douglas Applause shade raises or lowers unevenly?
If your Hunter Douglas Indoor Furnishing shade raises or lowers unevenly, start by checking that the headrail and installation brackets are level and aligned, shimming the brackets if necessary. Also, check for any obstructions in the shade's path that may cause misalignment. Try lowering the shade completely, then raising it to allow it to self-correct. For further adjustments, see Shade Height Adjustment on page 11.
How to shorten the tassel cord on Hunter Douglas Applause Indoor Furnishing?
To shorten the Hunter Douglas Indoor Furnishing tassel cord, grasp both parts of the tassel (the colored cover and the frosted body). Squeeze the tassel cover with your thumb and forefinger (at the 's' of the Hunter Douglas Cord logo). Separate and slide the tassel cover off from the tassel body. Pull out the knotted end of the tassel cord. Retie the cord at the desired shorter length, using a double knot. Trim the tassel cord. Pull the trimmed knot up inside the tassel. Squeeze the sides of the tassel cover together while sliding it back onto the tassel body. Ensure there are no gaps between the two components after reassembling, and that they do not pull apart easily. The tassel cover should be securely seated into the tassel body.
What to do if lift cords hang from the bottom rail of my Hunter Douglas Applause?
If lift cords are hanging from the bottom rail, tape the extra cord length to the bottom rail or place it into the groove on the bottom rail for future adjustments.
Why Hunter Douglas Indoor Furnishing shade raises or lowers unevenly?
The shade may be skewing. Lower the shade completely to allow it to self-correct. Pull the cord loop slowly to prevent further skewing. Ensure the headrail and installation brackets are level (shim if needed). For Top-Down/Bottom-Up shades, lower each rail completely to allow them to self-correct if the cord was pulled too quickly.
Why Hunter Douglas Indoor Furnishing shade will not fit into the installation brackets?
Make sure the installation brackets are level and aligned, using shims if necessary. Ensure the screw heads are flush against the brackets and the headrail is fully inserted.
What to do if Hunter Douglas Indoor Furnishing shade is hard to raise or lower?
First, ensure the cord tensioner is correctly mounted. If you have Duolite™ or Top-Down/Bottom-Up shades, the lift cords in the headrail may have overturned. Try pulling down the back cord of the cord loop (if both rails are raised) or the front cord (for other problems). Also, check that the shade fabric isn't caught, the headrail and brackets are level (shim if needed), cords aren't pinched, and hold-down brackets are released.
Provides an illustrated overview of the shade's components and types.
Lists all required tools and fasteners for proper installation.
Explains the general process and bracket requirements for installation.
Defines different window mounting styles and terminology.
Detailed instructions for mounting brackets (Inside, Outside, End Mount).
Steps to attach the shade, cord tensioner, and operating wand.
How to correctly raise and lower the shade using the cord loop.
Instructions for magnetic hold-down brackets and leveling the shade rails.
Solutions for common issues encountered during shade operation.
Procedures for detaching the shade and cleaning its fabric.
Guidelines for water immersion, ultrasonic, and extraction cleaning.
Critical safety instructions for cord loops and tensioner installation.
General| Material | Fabric |
|---|---|
| Style | Pleated |
| UV Protection | Yes |
| Privacy | Yes |
| Operating Systems | Manual, Motorized |
| Light Control | Light Filtering, Room Darkening |
| Cell Size | 3/8", 3/4" |
| Lift System | Cordless Motorized |
| Construction | Single Cell |
| Operation | Manual Motorized |
To Next Page