HunterDouglas Provenance User Manual (English)

Other manuals for HunterDouglas Provenance

Installation Operation Care20 pages

Installation And Care Instructions3 pages

Questions and Answers:

S
stacey85Aug 13, 2025
Why does my HunterDouglas Provenance shade raise unevenly?
- L
  Lisa JordanAug 13, 2025
  To address this issue, first, ensure that the headrail and installation brackets are level and properly aligned. If needed, use shims to level the headrail. Also, check for any obstructions that might be interfering with the shade's movement. If the shade encounters an obstruction while being lowered, it can become misaligned, leading to uneven raising or a tilted bottom rail when fully raised. Try fully lowering the shade and then raising it again to allow it to self-correct.
J
jamesdaisyAug 17, 2025
What to do if my HunterDouglas Indoor Furnishing shade is hard to raise or lower?
- D
  David VaughnAug 18, 2025
  First, ensure the shade fabric isn't caught between the installation bracket and the headrail. Then, verify that the headrail and installation brackets are level and aligned; use shims to level the headrail if necessary. If hold-down brackets are in use, confirm they've been released before operating the shade.
B
bradfordwhitneyAug 21, 2025
How to fit HunterDouglas Provenance Indoor Furnishing shade into installation brackets?
- J
  Justin ReedAug 21, 2025
  Ensure that the installation brackets are level and aligned. Use shims (provided) to level the headrail, if needed. Make sure the screw heads are flush against the installation bracket. Confirm that the headrail is fully inserted into the installation brackets.
B
barnesmariaAug 26, 2025
What to do if HunterDouglas Provenance drapery does not open or close easily?
- J
  Jonathan CooperAug 26, 2025
  If your HunterDouglas Indoor Furnishing drapery isn't opening or closing smoothly, there are several things you can check: * Ensure the cord tensioner is correctly mounted. * Verify the drapery is attached properly to the carriers, alternating between the front and back tracks. * Confirm the installation brackets are level and the mounting clips are aligned. * Make sure there are no obstructions hindering the drapery's movement, such as a cord caught in the brackets. * Operate the wand correctly by holding it at a 45 degree angle and pulling or pushing it toward the desired side. * Try lightly spraying dry silicon lubricant inside the carrier track.
J
Jillian RussellAug 28, 2025
How to shorten the cord for the HunterDouglas Provenance Universal Cord Tensioner?
- G
  greenmatthewAug 28, 2025
  If the cord on your HunterDouglas Indoor Furnishing Universal Cord Tensioner is too long, you can adjust it. First, mount the UCT to the wall in the desired position. Pull each cord to find the one that doesn't move the carriers; this is the adjustable cord, possibly marked with a black dot (except on cocoa or black cords). Use needle-nose pliers to pull the cord knot from the cord driver in the headrail. Pull the cord taut so the loop moves freely through the tensioner. Mark the cord near the driver (use white on cocoa or black cords). Remove the UCT, tie a double knot at the mark, and let it retract into the driver. Re-attach the UCT, ensuring the cord is taut and moves easily. Repeat if needed, then cut any excess cord below the knot.
A
adam90Sep 1, 2025
Why is my HunterDouglas Indoor Furnishing drapery not hanging correctly?
- T
  Thomas BrownSep 1, 2025
  If your HunterDouglas Indoor Furnishing drapery isn't hanging correctly, make sure the drapery is attached to the carriers correctly, alternating between the front and back tracks. Also, check that the headrail is level and that there are no obstructions to the drapery or its movement, such as a cord caught in the brackets.
A
Alicia TaylorSep 5, 2025
What to do if HunterDouglas Provenance Universal Cord Tensioner has climbed to the headrail?
- J
  john51Sep 5, 2025
  If the Universal Cord Tensioner (UCT) on your HunterDouglas Indoor Furnishing has climbed to the headrail, here's what to do: Insert a small screwdriver, punch, or awl through the screw hole in the Universal Cord Tensioner. Pull down on the screw hole to relieve the tension on the UCT. Pull the entire UCT to the bottom of the cord loop. Properly mount the UCT and attach the cord tensioner according to the instructions provided with the UCT Installation Kit.
F
Frank LawsonSep 9, 2025
Why does my HunterDouglas Indoor Furnishing Universal Cord Tensioner grab the cord when I use it?
- S
  santoschelseaSep 9, 2025
  If the Universal Cord Tensioner is grabbing onto the cord when you operate your HunterDouglas Indoor Furnishing, ensure the cord tensioner is mounted correctly. If necessary, check the Universal Cord Tensioner Installation Instructions included with your drapery and reinstall the tensioner.