What to do if my HunterDouglas Window Blind does not stay in place as the wand or cord retracts during raising?
If your UltraGlide HunterDouglas Window Blind does not stay in place as the wand or cord retracts during raising, the lowering mechanism has likely been engaged. Make sure you pull down on the pull wand or cord to raise the blind, instead of pulling out or across it.
What to do if HunterDouglas Indoor Furnishing EasyRise cord tensioner has climbed to the headrail?
If the universal cord tensioner has climbed to the headrail, pull down on the spring to relieve tension and pull the universal cord tensioner to the bottom of the cord loop. Properly mount the cord tensioner, referring to the Universal Cord Tensioner Installation Instructions included with your HunterDouglas shading.
Why HunterDouglas Window Blinds UltraGlide don't stay in place when raising?
If your HunterDouglas UltraGlide blinds don't stay in place as the wand or cord retracts during raising, it's likely that the lowering mechanism has been engaged. Make sure you're pulling down on the pull wand or cord, and not out or across the blind.
How to open vanes on HunterDouglas UltraGlide Indoor Furnishing LiteRise shadings?
To open the vanes on your HunterDouglas LiteRise shading, place your thumb on the front of the handle and your fingers on the back. Gently pull the back of the handle down and away from the shading. Note that the shading must be fully lowered to tilt it open.
Why vanes do not align on side-by-side HunterDouglas UltraGlide Indoor Furnishing shadings?
Vane alignment is only guaranteed within 1/4" when HunterDouglas shadings are ordered at the same time, at the same height, with the same colour and fabric, and when specified on the order form. Check that the windows are square and the same height.
What to do if the bottom rail of my HunterDouglas Window Blinds with PowerView® Gen 3 doesn't raise or lower completely?
If the bottom rail of your HunterDouglas Window Blinds does not raise or lower completely, or its fully lowered position has changed, the batteries in the battery wand or satellite battery pack may be low. Try replacing the batteries. Also, make sure the power source is securely connected to the power cable and that the cables aren't pinched or caught in the headrail or installation brackets.
Why are my HunterDouglas Window Blinds hard to raise or lower?
If your HunterDouglas Window Blinds are hard to raise or lower, or won't move at all, and they're an inside mount, make sure the headrail is installed correctly. Shadings should not be forced into tight inside mount window openings.
How to install HunterDouglas Window Blinds if they don't fit into brackets?
If the HunterDouglas Window Blind won't fit into the installation brackets, ensure the brackets are level and aligned, and the mounting surface is flat.
What to do if HunterDouglas Window Blinds do not tilt?
If your HunterDouglas Window Blinds don't tilt, check that the tilt cords aren't tangled or knotted. Also, make sure the ladders haven't become disengaged from the tape rolls and that the tilt rod is fully inserted into the tilt gear.
How to fix HunterDouglas Window Blinds that don't raise or lower evenly?
If your HunterDouglas Window Blinds don't raise or lower evenly, check inside the headrail for any obstructions that might be preventing the mechanism from turning. Also, make sure the lift cords aren't pinched or tangled.
General| Material | High-quality fabrics, various options available |
|---|---|
| Light Filtering | Yes, varies by fabric selection |
| Privacy | Varies by shade/blind; from light filtering to room darkening |
| UV Protection | Yes, varies by fabric selection |
| Customization | Available in a wide range of fabrics, colors, and styles |
To Next Page
