What to do if Husqvarna 535i XP Chainsaw motor makes sudden movement, then stops?
If the electrical motor of your Husqvarna Chainsaw makes a sudden movement when you push the power trigger and then stops, it is likely due to a short circuit in the control unit. Replace the control unit.
What to do if Husqvarna 535i XP shows red light after installing a new control unit?
If your Husqvarna Chainsaw shows a red light after installing a new control unit, it may be because the spare part comes without software. Use a diagnostic tool to install the software.
What to do if Husqvarna 535i XP Chainsaw charger does not start?
If the Husqvarna Chainsaw charger doesn't start and no LEDs light up when the battery is attached, check the following: ensure the connection between the charger and battery is clean and undamaged. Also, check the battery. If the issue persists, the charger itself may be defective. Disconnect the charger from the mains outlet for at least 1 minute, then reconnect it. Verify that the fan starts and a green LED illuminates for about 3 seconds. If not, replace the charger.
What to do if a warning sign flashes red on the battery of Husqvarna Chainsaw?
If a warning sign flashes red on the Husqvarna Chainsaw battery when you press the start button, it could be due to several reasons: the battery temperature might be too high (wait until it cools down, or insert it into the charger to cool it faster), the voltage might be too low (charge the battery), the temperature could be too low (ensure the battery temperature is above -10° C), or the battery itself might be defective (replace it).
Why Husqvarna 535i XP won't start and no LEDs are on?
If your Husqvarna Chainsaw doesn't start and no LEDs light up when you press the power button, there could be several reasons. First, the battery might be defective; press the on/off button to check the battery – at least one green LED should illuminate. Other potential causes include a defective connection between the battery and the product (ensure the connectors are clean and undamaged), a faulty connection in the keypad connector (make sure it's correctly assembled, dry, undamaged, and free from corrosion), a broken keypad (replace it), damaged cables between the control unit and keypad/main switch (repair or replace them if damaged), or a short circuit in the control unit (replace it).
What to do if the red error LED comes on on my Husqvarna 535i XP Chainsaw?
The red error LED indicates that the cell difference is too much (1V). Speak to your servicing dealer.
Why is the warning indicator flashing on my Husqvarna Chainsaw?
The warning indicator flashes because of a temperature deviation. To resolve this, ensure the battery is used in surroundings where temperatures are between 5°C/41°F and 40°C/104°F.
General| Battery Voltage | 36 V |
|---|---|
| Weight (excluding battery and cutting equipment) | 2.6 kg |
| Chain Speed at Max Power | 20 m/s |
| Sound Pressure Level at Operator's Ear | 94 dB(A) |
| Recommended Bar Length | 12-16 inches |
| Oil Tank Volume | 0.2 liters |
| Chain Pitch | 3/8 inch |
| Chain Gauge | 0.043 in |
Defines the product's purpose in forest service for felling, limbing, and cutting.
Illustrates and labels the components of the chainsaw model.
Introduces the 330i and 535i XP chainsaw models with an electrical motor.
Explains safety warnings and operational symbols found on the product itself.
Details symbols related to battery and charger safety and disposal, especially for Europe.
Provides definitions for warning levels and general safety precautions for power tool operation.
Covers maintaining a safe work environment and essential electrical safety measures.
Emphasizes personal alertness, protective gear, and proper attire for safe operation.
Details critical safety warnings and techniques specific to operating a chain saw, including kickback prevention.
Outlines crucial safety instructions for handling and using batteries and battery chargers.
Highlights safety precautions and requirements before performing any maintenance on the product.
Step-by-step guide for attaching the guide bar and saw chain to the 330i model.
Step-by-step guide for attaching the guide bar and saw chain to the 535i XP model.
Instructions for installing a spiked bumper, referring to a servicing dealer.
Essential functional checks to perform before using the chainsaw for safety and proper operation.
Procedures for connecting the battery charger and charging the battery.
Step-by-step instructions on how to safely start and stop the chainsaw.
Explains the causes of kickback and how to prevent it through correct working technique.
Details various cutting techniques, including basic cuts, limbing, and felling.
Covers safe tree felling, including distance, direction, preparation, and specific cuts.
Guidance on safely cutting trees and branches that are under tension.
Procedures for regularly checking the functionality and condition of safety devices.
Instructions for checking key components like the trigger, brake, catcher, keypad, battery, and cooling system.
Detailed steps for sharpening the saw chain and adjusting the depth gauge for optimal performance.
Guidance on proper chain tensioning and checking saw chain lubrication.
How to inspect the guide bar, chain, and drive sprocket for wear and perform necessary maintenance.
Explains possible fault codes displayed on the keypad and their corresponding actions.
Lists common problems with the battery and charger, along with solutions.
Provides key technical specifications for the 330i and 535i XP models.
Lists recommended guide bar and saw chain combinations approved for the product.
Specifies approved battery models and compatible battery chargers.
Official declaration of the product's conformity with relevant EU directives and standards.
To Next Page
