What does it mean if guide calibration failed on my Husqvarna Lawn Mower?
If the guide wire calibration has failed on your Husqvarna Lawn Mower, verify that the guide wires are installed according to instructions and then perform a new calibration.
What to do if there is a front loop sensor problem on my Husqvarna Automower 305?
If you're experiencing a front loop sensor problem on your Husqvarna Lawn Mower, it could be due to a faulty or loose cable to the sensor circuit board; check the cabling and refit or replace if necessary. The front loop sensor circuit board itself might be faulty, so check and replace it if needed. An electronic or software issue within the product could also be the cause; check the levels for the A signal.
What causes the left wheel motor to be blocked on my Husqvarna Automower 305?
The left wheel motor of your Husqvarna Lawn Mower can become blocked if grass or another object has wrapped around the drive wheel. To resolve this, check the drive wheel and remove any obstructions.
Why does my Husqvarna Automower 305 have low battery voltage?
A low battery voltage in your Husqvarna Lawn Mower can stem from a few reasons. First, ensure the mower can find the charging station by verifying that the charging station and guide wire are installed correctly. Check if the guide wire is broken or not connected by looking at the indicator light on the charging station. If the battery is spent, replace it. Also, a defective charging station antenna can cause this issue; check if the indicator light on the charging station flashes red.
How to troubleshoot low battery on Husqvarna Lawn Mower?
If you're experiencing low battery issues with your Husqvarna Lawn Mower, consider these potential causes: The product may be unable to locate the charging station, so try repositioning the guide wire. Check the installation settings related to finding the charging station. The battery itself might be spent, requiring a battery test. Also, the charging station's antenna could be defective; look for a red flashing indicator lamp and replace the baseplate if needed.
What to do if my Husqvarna Automower 305 Lawn Mower has a battery problem?
If your Husqvarna Lawn Mower has a battery problem, check that the battery is properly connected. Also, ensure that you are using only original batteries recommended by the manufacturer.
How to fix 'No loop signal' on a Husqvarna Automower 305?
The 'No loop signal' message on your Husqvarna Lawn Mower can appear if the boundary wire is crossed on its way to and from an island. Check that the boundary wire is laid according to instructions, ensuring it's in the correct direction around any islands. Also, disturbances from metal objects (fences, reinforcement steel) or buried cables nearby can cause this issue. Try moving the boundary wire or creating islands in the work area to boost the signal strength. Another possibility is that the mower is too far from the boundary wire. Redo the boundary wire installation to ensure all parts of the work area are a maximum of 35 m / 115 ft from the boundary wire.
What to do if Husqvarna Lawn Mower shows battery problem?
If you are experiencing a battery problem with your Husqvarna Lawn Mower, first ensure the battery is correctly connected by removing the battery cover and checking the connector. Also, verify that you are using an original Husqvarna battery, as the wrong type of battery can cause issues.
What to do if my Husqvarna Lawn Mower goes outside the working area?
If your Husqvarna Lawn Mower is operating outside the designated working area, several factors could be responsible. First, check that the boundary wire connections to the charging station are correctly connected. Also, make sure that the boundary wire isn't too close to the edge of the working area and that it's properly installed according to the manual. If the working area has slopes, ensure they aren't too steep. The boundary wire may also be routed incorrectly around an island. Metal objects or buried cables can also cause interference. If there is another mower installation close by, park your mower in the charging station and generate a new loop signal via Security -> New loop signal (3-3).
What to do if the blade disc is blocked on my Husqvarna Automower 305?
If the blade disc on your Husqvarna Lawn Mower is blocked, it could be due to grass or another object wrapped around it. Check the blade disc and remove any obstructions. Another cause could be that the blade disc is sitting in a pool of water. Move the mower and try to prevent water from collecting in the working area.
General| Cutting Width | 22 cm |
|---|---|
| Cutting Height Min | 20 mm |
| Cutting Height Max | 50 mm |
| Battery Type | Li-Ion |
| Typical Charging Time | 60 min |
| Sound Level Measured | 59 dB(A) |
| Area Capacity | 600 m² |
| Maximum Incline within the Working Area | 40% |
| Weight | 9.4 kg |
| Rain Sensor | Yes |
| Anti-Theft Alarm | Yes |
| Blade Type | 3 pivoting blades |
| Typical Mowing Time per Charge | 60 minutes |
| Smartphone Connectivity | Automower® Connect@Home |
Crucial safety guidelines for operating and maintaining the robotic lawnmower.
Guides on selecting the optimal location and securely installing the charging station.
Explains methods for laying the boundary wire and planning the working area layout.
Details the procedure for properly connecting the boundary wire to the charging station.
Covers the installation of the guide wire for improved navigation and remote area access.
Guides through initial setup, language, PIN, and automatic calibration procedures.
Procedure to confirm the mower can successfully dock with its charging station.
Step-by-step instructions for starting the robotic lawnmower.
Explains how to select operating modes like AUTO, MAN, and HOME.
Options for setting PIN codes, security levels, and managing loop signals.
Information on blade inspection, replacement, and their impact on performance.
Covers battery lifespan, replacement procedures, and care recommendations.
A detailed guide to locating and repairing breaks or faults in the boundary wire.
To Next Page
