What to do if my Husqvarna Automower 305 is trapped?
If your Husqvarna Lawn Mower is trapped, it means the mower has gotten caught on something. Free the mower and determine what caused it to get trapped, rectifying the issue. Also, if the mower frequently gets stuck behind obstacles, check if there are any obstacles that make it hard for the mower to move.
What to do if my Husqvarna Automower 305 Lawn Mower keypad is not working?
Make sure the cable between the HMI circuit board and the keypad is properly connected. You can also try replacing the keypad or the HMI circuit board.
What causes the left wheel motor to be blocked on my Husqvarna Automower 305?
The left wheel motor of your Husqvarna Lawn Mower can become blocked if grass or another object has wrapped around the drive wheel. To resolve this, check the drive wheel and remove any obstructions.
What happens if I enter the wrong PIN code on my Husqvarna Automower 305?
If you enter the wrong PIN code on your Husqvarna Lawn Mower, enter the correct PIN code. If you forget the PIN code, contact your local dealer.
Why is my Husqvarna Automower 305 Lawn Mower display lit but not responding?
If the display's backlighting is lit but the keypad and main switch don't respond on your Husqvarna Lawn Mower, the control box is defective. Reprogram the control box using Autocheck EXP, using the Advanced function and downloading the program manually.
Why is my Husqvarna Automower 305 showing mower tilted error?
If your Husqvarna Lawn Mower is tilted, it might be operating on a slope exceeding its limitations. Check that the tilt sensor is correctly calibrated, and calibrate if necessary. Consider adjusting the working area to exclude excessively steep slopes.
What does it mean if the charging current is too high on my Husqvarna Lawn Mower?
If your Husqvarna Lawn Mower indicates that the charging current is too high, it suggests a fault in the power supply, or the use of an incorrect power supply or charging station.
What to do if there is a rear loop sensor problem on my Husqvarna Automower 305 Lawn Mower?
If you're experiencing a rear loop sensor problem on your Husqvarna Lawn Mower, the rear loop sensor might be faulty, so check and replace the rear sensor circuit board if necessary. An electronic or software-related issue could also be the cause, so check the levels for the A signal. Additionally, the cabling to the sensor circuit board may be faulty or loose; check the cabling and refit it, or replace it if necessary.
What does a blue flashing light mean on my Husqvarna Lawn Mower charging station?
A blue flashing light on your Husqvarna Lawn Mower charging station indicates that the boundary loop is not connected to the charging station or there is a break in the boundary loop. Check that the boundary wire connector is fitted properly to the charging station. If there is a break in the boundary loop, find out where the break is and replace the damaged section with a new loop wire, splicing it using an original connector.
What does a yellow flashing light mean on my Husqvarna Automower 305 Lawn Mower charging station?
A yellow flashing light on your Husqvarna Lawn Mower charging station means that the guide wire is not connected to the charging station or there is a break in the guide wire. Check that the guide wire connector is properly connected to the charging station. If there is a break in the guide wire, find it and replace the damaged section with a new loop wire, splicing it using an original connector.
General| Cutting Width | 22 cm |
|---|---|
| Cutting Height Min | 20 mm |
| Cutting Height Max | 50 mm |
| Battery Type | Li-Ion |
| Typical Charging Time | 60 min |
| Sound Level Measured | 59 dB(A) |
| Area Capacity | 600 m² |
| Maximum Incline within the Working Area | 40% |
| Weight | 9.4 kg |
| Rain Sensor | Yes |
| Anti-Theft Alarm | Yes |
| Blade Type | 3 pivoting blades |
| Typical Mowing Time per Charge | 60 minutes |
| Smartphone Connectivity | Automower® Connect@Home |
Crucial safety guidelines for operating and maintaining the robotic lawnmower.
Guides on selecting the optimal location and securely installing the charging station.
Explains methods for laying the boundary wire and planning the working area layout.
Details the procedure for properly connecting the boundary wire to the charging station.
Covers the installation of the guide wire for improved navigation and remote area access.
Guides through initial setup, language, PIN, and automatic calibration procedures.
Procedure to confirm the mower can successfully dock with its charging station.
Step-by-step instructions for starting the robotic lawnmower.
Explains how to select operating modes like AUTO, MAN, and HOME.
Options for setting PIN codes, security levels, and managing loop signals.
Information on blade inspection, replacement, and their impact on performance.
Covers battery lifespan, replacement procedures, and care recommendations.
A detailed guide to locating and repairing breaks or faults in the boundary wire.
To Next Page
