Hytera RD625 User Manual (English)

Other manuals for Hytera RD625

Questions and Answers:

M
Marcia TurnerAug 13, 2025
Why is the communication distance short and voice quality poor on my Hytera Repeater?
- J
  Johnny LopezAug 13, 2025
  If the communication distance is short and the voice quality is poor when using your Hytera Repeater, there might be a signal loss due to connecting cable damage. Inspect the cable for any significant damage and replace it if necessary. Also, check if the antenna and cable connections are loose or disconnected. Secure these connections, and replace the connector if needed. Internal damage to the cable can also cause this issue, so consider replacing the cable. If a duplexer is installed, it might be improperly adjusted, in which case you should contact Hytera or your local dealer for readjustment.
M
Marc Adams IIAug 17, 2025
How to troubleshoot power-on failure on Hytera RD625?
- N
  Nicholas MartinAug 17, 2025
  If your Hytera Repeater fails to power on, first ensure the power cord is properly and securely connected to the outlet. Next, check the DC power fuse for any damage and replace it if necessary. Finally, verify that the DC power supply voltage is within the repeater's operating voltage range (13.6V±15%) and adjust if needed.
B
Brad AndersonAug 20, 2025
What to do if RX is indicated, but Hytera Repeater members can't communicate?
- C
  Christopher James PhDAug 20, 2025
  If you have RX indication on the radios but members cannot communicate with each other via your Hytera Repeater, ensure that the Radio ID matches that of all other members. Also, check whether the CTCSS/CDCSS settings are consistent across all radios; reset them if necessary.
E
Eric PenaAug 25, 2025
Why can't my radio communicate with other members through the Hytera Repeater?
- R
  rogerconradAug 25, 2025
  If your radio is unable to communicate with other members through the Hytera Repeater, check that the TX/RX frequency of the repeater is consistent with that of the portable/mobile radios; reset the frequencies if they are not. If strong interference signals are present, try to remove or bypass the interference source, or change to operate at other frequencies. Also, verify that the radio is within the coverage area of the repeater.
M
Melissa McdanielAug 28, 2025
What to do if my Hytera Repeater fails to power on?
- L
  Luis BurgessAug 28, 2025
  If your Hytera Repeater fails to power on, there are several potential causes. First, ensure the power cord is properly and securely connected to the outlet. Next, check the DC power fuse for any damage and replace it if necessary. Finally, verify that the DC power supply voltage is within the repeater's operating range of 13.6V±15%, and adjust if needed.
B
Billy WrightSep 1, 2025
Why is my Hytera RD625 not allowing communication between radios?
- E
  Erin WrightSep 1, 2025
  If radios can't communicate via the Hytera Repeater, several factors could be at play. Check that the TX/RX frequencies of the repeater match those of the portable/mobile radios, and reset them if needed. Also, strong interference signals may be preventing the repeater from relaying the signal; try changing to different frequencies if you cannot remove the interference. Finally, ensure that the radios are within the repeater's coverage area.
B
Brittany PowellSep 5, 2025
How to fix short communication distance and poor voice quality on Hytera Repeater?
- C
  ccainSep 5, 2025
  Poor voice quality and short communication distance on your Hytera Repeater can stem from a few issues. Begin by inspecting the connecting cable for any damage, replacing it if the damage is significant. Next, check the antenna and cable connections to ensure they are secure, replacing the connector if necessary. Finally, internal cable damage can also cause these issues, so consider replacing the cable.
J
johnibarraSep 8, 2025
What to do if there's RX indication but Hytera RD625 Repeater users can't communicate?
- E
  evanselizabethSep 8, 2025
  If your Hytera Repeater shows an RX indication but users can't communicate, the issue might be related to mismatched settings. Ensure that the radio ID is the same for all members. Also, verify that the CTCSS/CDCSS settings are consistent across all radios, and reset them if necessary.

Hytera RD625 Specifications

General

Output Power	25W
Operating Temperature	-30°C to +60°C
Modulation	4FSK
IP Rating	IP54
Frequency Range	400-470 MHz
Channel Capacity	16
Power Supply	AC: 100-240V, 50/60Hz
Digital Protocol	DMR