EasyManuals Logo

IBM System x3400 M3 Types 7378 User Manual

IBM System x3400 M3 Types 7378
154 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #132 background imageLoading...
Page #132 background image
Using the LSI Configuration Utility program
Use the LSI Configuration Utility program to configure and manage redundant array
of independent disks (RAID) arrays. Be sure to use this program as described in
this document. Use the LSI Configuration Utility program to perform the following
tasks:
v Perform a low-level format on a hard disk drive
v Create an array of hard disk drives with or without a hot-spare drive
v Set protocol parameters on hard disk drives
The integrated SAS/SATA adapter with RAID capabilities supports RAID arrays. You
can use the LSI Configuration Utility program to configure RAID 1 (IM), RAID 1E
(IME), and RAID 0 (IS) for a single pair of attached devices. If you install a different
type of RAID adapter, follow the instructions in the documentation that comes with
the adapter to view or change settings for attached devices.
In addition, you can download an LSI command-line configuration program from
http://www.ibm.com/systems/support/.
When you are using the LSI Configuration Utility program to configure and manage
arrays, consider the following information:
v The integrated SAS/SATA adapter with RAID capabilities supports the following
features:
Integrated Mirroring (IM) with hot-spare support (also known as RAID 1)
Use this option to create an integrated array of two disks. All data on the
primary disk can be migrated.
Integrated Mirroring Enhanced (IME) with hot-spare support (also known as
RAID 1E)
Use this option to create an integrated mirror enhanced array of three to eight
disks. All data on the array disks will be deleted.,
Integrated Striping (IS) (also known as RAID 0)
Use this option to create an integrated striping array of two to eight disks. All
data on the array disks will be deleted.
v Hard disk drive capacities affect how you create arrays. The drives in an array
can have different capacities, but the RAID adapter treats them as if they all
have the capacity of the smallest hard disk drive.
v If you use an integrated SAS/SATA adapter with RAID capabilities to configure a
RAID 1 (mirrored) array after you have installed the operating system, you will
lose access to any data or applications that were previously stored on the
secondary drive of the mirrored pair.
v If you install a different type of RAID adapter, see the documentation that comes
with the adapter for information about viewing and changing settings for attached
devices.
Starting the LSI Configuration Utility program
To start the LSI Configuration Utility program, complete the following steps:
1. Turn on the server.
Note: Approximately 20 seconds after the server is connected to AC power, the
power-control button becomes active.
116 IBM System x3400 M3 Types 7378 and 7379: Installation and User's Guide

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the IBM System x3400 M3 Types 7378 and is the answer not in the manual?

IBM System x3400 M3 Types 7378 Specifications

General IconGeneral
ProcessorIntel Xeon 5600 series
Memory Slots12 DIMM slots
Hard Drive BaysUp to 8 bays
Network InterfaceDual Gigabit Ethernet
ManagementIntegrated Management Module (IMM)
Form FactorTower
Processor Cores4 or 6 cores
ChipsetIntel 5520
StorageSAS/SATA
RAID SupportRAID 0, 1, 10
Power SupplyRedundant Power Supply Options Available
Expansion Slots4 PCI-Express slots
USB Ports6 USB 2.0
Operating System SupportMicrosoft Windows Server, Red Hat Enterprise Linux, SUSE Linux Enterprise Server, VMware

Related product manuals