Icom IC-9100 - Specifications

1 - 1
SECTION 1
.
SPECIFICATIONS
■ General
• Frequency coverage : (unit: MHz)
Receive
0.030–60.000*
1
*
2
136.000–174.000*
1
*
2
420.000–480.000*
1
*
2
1240.000–1320.000
†
Transmit
1.800–1.999*
2
, 3.500–3.999*
2
,
5.330500*
3
, 5.346500*
3
, 5.366500*
3
,
5.371500*
3
, 5.403500*
3
,
7.000–7.300*
2
, 10.100–10.150*
2
,
14.000–14.350*
2
, 18.068–18.168*
2
,
21.000–21.450*
2
, 24.890–24.990*
2
,
28.000–29.700*
2
, 50.000–54.000*
2
144.000–148.000*
2
, 430.000–450.000*
2
1240.000–1300.000
†
*
1
Some frequency bands are not guaranteed.
*
2
Depending on version. *
3
USA version only. USB mode only.
• Mode : USB, LSB, CW, RTTY, AM, FM,
DV*
*The optional UT-121 is required.
• No. of memory channels : 297CH (99CH × 3 band)
(
396CH with UX-9100
‡
; 99CH × 4
bands)
• No. of scan edge
memory channels : 18CH
(6 × 3 band)
( 24CH with UX-9100
‡
; 6CH × 4
bands
)
• No. of call channels : 3CH
(1 × 3 band)
( 4CH with UX-9100
‡
; 1CH × 4
bands
)
• No. of Satellite
memory channels : 20CH
• Antenna connector : SO-239 × 3
Type-N × 2*
*When the optional UX-9100 is installed.
• Antenna impedance : 50 Ω
(at Antenna Tuner OFF)
• Usable temperature range : 0˚C to +50˚C (+32˚F to +122˚F)
• Frequency stability : Less than ±0.5 ppm 5 min. after
power ON.
(0˚C to +50˚C; +32˚F to
+122˚F)
• Frequency resolution : 1 Hz
• Power supply :
13.8 V DC ±15% (negative ground)
• Power consumption
Transmit
Max. power : 24.0 A
(HF/50/144/430 MHz band)
11.0 A (1200 MHz band)
†
Receive
Standby : 3.0 A
(HF/50/144/430 MHz band)
4.0 A (1200 MHz band)
†
Max. audio : 4.5 A (HF/50/144/430 MHz band)
5.5 A (1200 MHz band)
†
• Dimensions : 315(W) × 116(H) × 343(D) mm
(projections not included) 12.4(W) × 4.57(H) × 13.5(D) in
• Weight (approximately) : 11.0 kg; 24.2 lb
11.95 kg; 26.3 lb
(with UX-9100)
• ACC connector : 13-pin
• CI-V connector : 2-conductor 3.5 (d) mm (
1
⁄
8
″)
■ Transmitter
• Output power (continuously adjustable)
Frequency band Output power
HF/50 MHz 2 to 100 W (AM: 2 to 30 W)*
144 MHz 2 to 100 W
430 MHz 2 to 75 W
1200 MHz
†
1 to 10 W
(at 13.8 V DC/+25˚C)
* In the AM mode, transmission can be performed only on
the HF/50 MHz frequency band.
• Modulation system
SSB : Digital PSN modulation
AM : Digital Low power modulation
FM : Digital Phase modulation
DV* :
GMSK Digital Phase modulation
*The optional UT-121 is required.
• Spurious emission
(Spurious domain)
HF bands : Less than –50 dB
50/144 MHz band : Less than –63 dB
430 MHz band : Less than –61.8 dB
1200 MHz band
†
: Less than –53 dB
(Out-of-band domain)
HF bands : Less than –40 dB
50/144/430 MHz band : Less than –60 dB
1200 MHz band
†
: Less than –50 dB
• Carrier suppression : More than 40 dB
• Unwanted sideband
suppression : More than 55 dB
(1200 MHz: More than 40 dB)
†
• TX variable range : ±9.999 kHz
• Microphone connector : 8-pin connector
• Microphone impedance : 600
Ω
• ELEC-KEY connector : 3-conductor 6.35(d) mm (
1
⁄
4
″)
• KEY connector :
3-conductor 6.35(d) mm (
1
⁄
4
″)
• SEND connector : Phono jack
(RCA)
• ALC connector : Phono jack (RCA)
†
The optional UX-9100 is required for 1200 MHz frequency band operation.
‡
Only when the 1200 MHz frequency band is selected.