Icom IC-9100 - Transmit Adjustments

ADJUSTMENT ITEM
TRANSCEIVER'S
CONDITION
OPERATION
MEASURE
POINT
ADJUST
POINT
VALUE
PREPARATION
–
• Connect an AG and millivoltmeter
to [MIC], and then set it as;
Frequency : 1.5 kHz
Level : 1 mV
• Connect a power meter to [ANT1].
•
Connect a 25
Ω
dummy load to [ANT2].
–– –
TX TOTAL GAIN 1 • Display: "Total Gain HF"
• Receiving
• Push [F-5]. (Automatically starts
to transmit.)
– [MAIN DIAL] 50 W
Push [F-5].
TX POWER & POWER
METER SETTING
2 • Display: "POWER HF"
• Receiving
• Push [F-5]. (Automatically starts
to transmit.)
– – Push [F-5].
3 • Display: "POWER HF Min"
• Transmitting
– [ANT1] [MAIN DIAL] 1.5 W
Push [F-5].
4 • Display: "POWER HF 10%"
• Transmitting
10 W
Push [F-5].
5 • Display: "POWER HF Tuner"
• Transmitting
10 W
Push [F-5].
6 • Display: "POWER HF 50%"
• Transmitting
50 W
Push [F-5].
7 • Display: "POWER HF 75%"
• Transmitting
80 W
Push [F-5].
8 • Display: "POWER HF 100%"
• Transmitting
105 W
Push [F-5].
9 • Display: "POWER 50M"
• Receiving
• Push [F-5]. (Automatically starts
to transmit.)
– – Push [F-5].
10 • Display: "POWER 50M Min"
• Transmitting
– [ANT1] [MAIN DIAL] 1.5 W
Push [F-5].
11 • Display: "POWER 50M 10%"
• Transmitting
10 W
Push [F-5].
12 • Display:
"POWER 50M Tuner"
• Transmitting
10 W
Push [F-5].
13 • Display: "POWER 50M 50%"
• Transmitting
50 W
Push [F-5].
14 • Display: "POWER 50M 75%"
• Transmitting
80 W
Push [F-5].
15 • Display:
"POWER 50M 100%"
• Transmitting
100 W
Push [F-5].
POWER DOWN SETTING 16 • Display:
"POWER Down HF/50M"
• Transmitting
• Push [F-5]. (Automatically starts
to transmit.)
– [MAIN DIAL] 50 W
Push [F-5].
AM CARRYER POWER
RATIO
17 • Display:
"POWER AM Ratio HF"
• Transmitting
• Push [F-5]. (Automatically starts
to transmit.)
– [MAIN DIAL] 27 W
Push [F-5].
ID APC 18 • Display: "ID-APC"
• Receiving
1) Connect an ammeter to the
power supply line.
2) Push [F-5]. (Automatically starts
to transmit.)
Power
supply line
[MAIN DIAL] 24–24.3 A
Push [F-5].
ALC METER 19 • Display: "ALC HF/50M"
• Transmitting
• Set the AG as;
Frequency : 1.5 kHz
Level : 10 mV
– – Push [F-5]
(A beep sounds,
and then another
beeps sound
3 sec. later)
DRIVE GAIN 20 • Display: "DRIVE HF/50M"
• Transmitting
– – Push [F-5].
SWR METER 21 • Display: "SWR HF/50M"
• Transmitting
– – Push [F-5].
Automatically returns to the transmit adjustment menu.
¤
TRANSMIT ADJUSTMENTS
• TRANSMIT ADJUSTMENTS (HF band)
• Transmit adjustment menu.
MENU
HF VHF UHF
TX
Reterns to the previous screen.
Starts the transmit adjustments (HF band).
(See below)
Starts the transmit adjustments (VHF).(Page 4-14)
Starts the transmit adjustments (UHF).
(Page 4-16)
Stores the value and move to the next item.
4 - 13