Icom IC-9700 - Page 18

D Command formats (Continued)
• Bandscope edge frequency settings
Command: 1A 05 0202 ~ 1A 05 0210
1 kHz: 0
~
9
100 Hz: 0 (fixed) 100 kHz: 0
~ 9
10 kHz: 0
~ 9
10 MHz: 0
~ 9
1 MHz: 0
~ 9
1 kHz: 0
~ 9
100 Hz: 0 (fixed) 100 kHz: 0
~ 9
10 kHz: 0
~ 9
10 MHz: 0
~ 9
1 MHz: 0
~ 9
q
X 0 X X X X X 0 X X X X
w e r t y
Lower edge Higher edge
• Manually entered position data
Command: 1A 05 0257, 0283, 0297, 23 02
X X X X
y ~ !1
∙∙∙∙∙∙∙
X X X X
!2 ~ !5
∙∙∙∙∙∙∙
X X
∙∙∙∙∙∙∙
X X
q ~ t
10 degree digit: 0 ~ 9
1 degree digit: 0 ~ 9 10 minute digit: 0 ~ 5 1 minute digit: 0 ~ 9 0.1 minute digit: 0 ~ 9 0.01 minute digit: 0 ~ 9 0.001 minute digit: 0 ~ 9 0 (Fixed) 0 (Fixed) South latitude=0/North latitude=1 0 (Fixed) 100 degree digit: 0 ~ 1 10 degree digit: 0 ~ 9 1 degree digit: 0 ~ 9 10 minute digit: 0 ~ 5 1 minute digit: 0 ~ 9 0.1 minute digit: 0 ~ 9 0.01 minute digit: 0 ~ 9 0.001 minute digit: 0 ~ 9 0 (Fixed) 0 (Fixed)
West longitude=0/East longitude=1
Latitude Longitude
10000 meter digit: 0 ~ 1 1000 meter digit: 0 ~ 9 100 meter digit: 0 ~ 9 10 meter digit: 0 ~ 9 1 meter digit: 0 ~ 9 0.1 meter digit: 0 ~ 9 0 (Fixed)
+=0/–=1
Altitude
1
X X X X X X X 0 0 X 0 X X X X X X X X 0 0 X X X X X X X 0 X
2 3 4 5 6 7 8 9      
* * * *
:
q ~ t: Latitude (ddºmm.mmm format)
y ~ !1: Longitude (dddºmm.mmm format)
!2 ~ !5: Altitude (0.1 meter steps)
* When reading the contents with no altitude, sends
!2, !3, !4 and !5 as “FF.”
* When sending the contents with no altitude, set
!2, !3, !4 and !5 to “FF.”
• Unproto Address setting
Command: 1A 05 0259
Set an unproto address of up to 56 characters.
See “Codes for character entries.” (p. 15)
• Entering Object name or Item name
Command: 1A 05 0279, 0293
Enter an Object or Item name of up to 9 characters.
See “Codes for character entries.” (p. 15)
• D-PRS Symbol setting
Command: 1A 05 0262 ~ 1A 05 0265,
1A 05 0281, 0295, 0306
First digit Second digit
XX X X
⁄, \, 0 to 9, A to Z can be used for the rst digit
character.
See “Codes for character entries” for the second
digit character. (p.15)
• D-PRS Comment setting
Command: 1A 05 0268 ~ 1A 05 0271
1A 05 0282, 0296, 0308
Set a comment of up to 43 characters.
See “Codes for character entries.” (p. 15)
• GPS message setting
Command: 1A 05 0316
Set a GPS message of up to 20 characters.
See “Codes for character entries.” (p. 15)
• Alarm area (Group) setting
Command: 1A 05 0317
q
XX X X 0
w e
X
10 min.
digit: 0 ~ 5
1 min.
digit: 0 ~ 9
0.1 min.
digit: 0 ~ 9
0.01 min.
digit: 0 ~ 9
0.001 min.
digit: 0 ~ 9
0 (fixed)
• Data mode with lter width settings
Command: 1A 06
q
X X X X
w
01=FIL1
02=FIL2
03=FIL3
00=Data mode OFF*
01=Data mode ON
*
When 00 is set, also set 00 to w
.
Remote control
17