• DV RX call sign data
Command: 20 0001, 20 0002
X X X X X XXX X X X X
∙∙∙∙∙∙
X XXX
∙∙∙∙∙∙
X X
∙∙∙∙∙∙
X X X X
∙∙∙∙∙∙
X X
~ ~
q Header ag data (First byte)
Data Description
bit7
(0: Fixed) —
bit6
(0: Fixed) —
bit5
(0: Fixed) —
bit4
0/1 0=Voice, 1=Data
bit3
0/1 0=Direct, 1=Through repeater
bit2
0/1 0=No Break-in, 1=Break-in
bit1
0/1 0=Data, 1=Control
bit0
0/1 0=Normal, 1=EMR
w Header ag data (Second byte)
Data
Description
bit2 bit1 bit0
1 1 1 Repeater control
1 1 0 Send auto acknowledge
1 0 1 (Not used)
1 0 0 Request to re-transmit
0 1 1 Send acknowledge
0 1 0 Receive no reply
0 0 1 Repeater disabled
0 0 0 NULL
e ~ !0: Call sign of the caller station
(8 characters, xed)
!1 ~ !4: Note of the caller station
(4 characters, xed)
!5 ~ @2: Call sign of the called station
(8 characters, xed)
@3 ~ #0: Call sign of the access/area repeater (R1)
(8 characters, xed)
#1 ~ #8: Call sign of the link/gateway repeater (R2)
(8 characters, xed)
LFF: When no call sign is received since the transceiver
power was turned ON.
D Command formats (Continued)
• DV RX message
Command: 20 0101, 20 0102
X X X XXX X X
∙∙∙∙∙∙
X X
∙∙∙∙∙∙
X X
q ~ @0: Message (20 characters)
@1 ~ @8: Call sign of the caller station (8 characters)
@9 ~ #2: Note of the caller station (4 characters)
See “Codes for character entries.” (p. 15)
LFF: When no call sign is received since the transceiver
power was turned ON.
Example: When a Gateway call is received
RXRPT2
RXRPT1
GW
CALLED
CALLER
JG3LUK calling
to JM1ZLK on
JP3YHH port A...
JG3LUK calling to
JM1ZLK on
JP3YHH port A...
INTERNETINTERNET
JM1ZLK on
JP3YHH port A...
CALLER: Caller’s call sign
CALLED: Called station call sign
RXRPT1: Call sign of the repeater that was
accessed by the caller station
L If it was a call through a gateway and the
internet, this item displays the gateway call
sign of the repeater you received the call from.
RXRPT2: Call sign of the repeater you received the
call from
• DV RX Status setting
Command: 20 0201, 20 0202
Data Function Description
bit7
0 (Fixed) —
bit6
0/1
Receiving a
voice call
While receiving a digital
voice signal, select “1.”
(Regardless of DSQL and
CSQL setting)
bit5
0/1
Last call
nisher
When the last call was
nished by you, select “1.”
bit4
0/1
Receiving a
signal
When the audio tone can
be heard, select “1.”
bit3
0/1
Receiving a
BK call
While receiving a BK call,
select “1.”
bit2
0/1
Receiving a
EMR call
While receiving a EMR call,
select “1.”
bit1
0/1
Receiving a
signal other
than DV
When “DV” and “FM” are
blinking, select “1.”
bit0
0/1
Packet loss
status
While displaying packet
loss, “1” is returned.
Remote control
20
To Next Page
Loading...
