Do not use a steam cleaner.
So as not to scratch the finish on the appliance, do not use sponges with a rough surface or abrasive cleaning agents.
To prevent corrosion, do not use sponge cloths on dishwashers with a stainless steel front or rinse such cloths thoroughly several times before using them for the first time.
Environmental protection and saving energy
Help protect the environment by using environmental protection and saving energy your appliance in a way that conserves resources and by disposing of reusable materials properly.
Disposing of packaging
The packaging materials are environmentally compatible and can be recycled.
● Sort the individual components by type and dispose of them separately. Information about current disposal methods is available from IKEA or your local authority.
Saving energy
If you follow these instructions, your appliance will use less electricity and less water.
Use the Eco 50 ° programme.
The Eco 50 ° programme is energy-efficient and environmentally friendly.
If you do not have much tableware to wash, use the additional Half Load function.
The programme will adjust to a lower load and consumption will be reduced.
Change the sensor setting to the default.
Consumption is reduced.
→ “Sensors”, Page 14
Drying automatically helps to save energy.
→ “Drying”, Page 13
Drying
The appliance is equipped with a container that has a mineral inside. This mineral can store moisture and heat energy and then release them again. Such drying lets you save
energy. During dishwashing heat energy is used to heat up the washing water and dry the mineral. During the drying phase moisture from the interior of the dishwasher is stored in
the mineral and heat energy is released. The heat energy is blown out into the interior of the dishwasher with dry air. This speeds up and improves drying. This drying method saves
a great deal of energy.
Tip: To avoid impairing the drying performance, do not position items of tableware directly in front of the intake opening or the blow opening of the container. Do not position heat-
sensitive items of tableware directly in front of the blow opening of the container. → “Appliance”, Page 17
AquaSensor
The AquaSensor is an optical measuring device (light barrier) that measures the turbidity of the washing water. You can save water with the AquaSensor. The use of the AquaSensor
depends on the programme. If the soiling level is low, the washing water is used in the next wash cycle, allowing water consumption to be reduced by 3-6 litres. If the soiling level is
higher, the washing water is drained off and replaced with fresh water. In the automatic programmes, the temperature and running time are additionally adjusted to the level of soiling.
Sensors
The sensors adjust the programme sequence and strength in the automatic programmes depending on the level and type of soiling. The sensor has different sensitivity settings that
can be changed in the basic settings. Installation and connection Installation and connection.
SENSOR
SETTING
DESCRIPTION
SE:00 The optimum setting for a mixed load and heavily soiled tableware. Saves both energy and water.
SE:01 Adjusts the programme strength for effective removal of food remnants even with low soiling levels. Energy and water consumption are adjusted accordingly.
SE:02
Adjusts the programme strength for difficult conditions of use, e.g. stubborn dried-on food remnants. Recommended setting when using organic or ecological
detergents containing low levels of active agents. Energy and water consumption are adjusted accordingly.
Installation and connection
Scope of supply
After unpacking all parts, check for any damage in transit and completeness of the delivery.
If you have any complaints, contact IKEA or our Customer Service.
Note: The appliance was tested at the factory to check it is in working order. It is possible that water has left marks on the appliance. These marks will disappear after the first wash
cycle.
The delivery consists of the following:
Dishwasher
Operating instructions
Installation Instructions
Installation material
Steam guard plate
Mains cable
Quick reference guide
Installing and connecting the appliance
You can position your built-under or integrable appliance in a fitted kitchen between wooden and plastic walls. If you subsequently install your dishwasher as a free-standing
appliance, you must stop it from tipping over, e.g. by screwing it to the wall or installing it under a continuous worktop that is securely connected to adjacent cabinets.
1. “Follow the safety instructions.”
→ Page 5
2. “Follow the instructions for electrical connection.” → Page 16
3. Check the Scope of supply and the condition of the appliance.
4. Consult the installation instructions for the installation dimensions required.
5. Make the appliance level using the height-adjustable feet. Make sure that the appliance is standing on the floor securely.
6. “Install the drainage connection.” → Page 15
7. “Install the drinking water connection.” → Page 15
8. Connect the appliance to the power supply.
Drainage connection
To Next Page
Loading...
