How to deal with the smell of gas from Immergas Victrix Tera 28 1?
If you smell gas from your Immergas Boiler, it's likely due to a leakage from the gas circuit pipelines. Immediately check the sealing efficiency of the gas intake circuit to resolve this issue.
What to do if Immergas Victrix Tera 28 1 safety thermostat activates frequently?
If your Immergas Boiler frequently activates the safety thermostat, it could be due to several reasons: 1. **Lack of water:** Ensure the system pressure is within the established limits by checking the pressure gauge. 2. **Poor water circulation:** Verify that the radiator valves are open to allow proper water flow. 3. **Blocked pump:** Check the functionality of the pump to ensure it's circulating water effectively.
Why does my Immergas Victrix Tera 28 1 have repeated ignition blocks?
Repeated ignition blocks in your Immergas Boiler can stem from a couple of issues: * **No gas supply:** Confirm there's pressure in the network and that the gas adduction cock is open. * **Incorrect gas cock adjustment:** Ensure the gas valve is correctly calibrated.
How to fix irregular combustion or noisiness in Immergas Boiler?
Irregular combustion or noisiness in your Immergas Boiler can be attributed to: * A dirty burner. Clean the burner and ensure correct installation of the terminal. * Incorrect combustion parameters. Check the correct setting of the gas valve (Off-Set setting) and the correct percentage of CO2 in the flue gas. * Intake-exhaust terminal not correctly installed. Clean the components and ensure correct installation of the terminal.
How to stop noise due to air in Immergas Victrix Tera 28 1 Boiler system?
If you notice noise due to air in the Immergas Boiler system: * Check the opening of the special air vent valve cap. * Make sure the system pressure and expansion vessel pre-charge values are within the set limits; The factory-set pressure values of the expansion vessel must be 1.0 bar, the value of system pressure must be between 1 and 1.2 bar.
What causes a blocked siphon in Immergas Boiler?
A blocked siphon in your Immergas Boiler might be due to dirt or combustion products deposited inside. To resolve this, check, by means of the condensate drain cap, that there are no residues of material blocking the flow of condensate.
General| Type | Condensing |
|---|---|
| Fuel Type | Natural Gas / LPG |
| DHW Output | 28 kW |
| Heat Exchanger Material | Stainless Steel |
| Protection Rating | IPX5D |
| Dimensions (H x W x D) | 748 x 440 x 256 mm |
| Max working temperature | 90°C |
| Electrical connection | 230 V / 50 Hz |
| NOx Class | 6 |
| Water pressure | 0.3 - 3 bar |
Provides essential guidelines and advice for proper boiler installation.
Outlines regulations and standards for safe boiler installation locations and methods.
Specifies required clearances around the boiler for safe operation and maintenance.
Details the boiler's antifreeze function and protection measures against freezing.
Describes the procedure for installing the boiler in an optional recessed frame.
Explains the components and connection of the optional boiler connection unit.
Covers essential aspects of connecting the gas supply to the boiler, including safety.
Details the procedures and requirements for connecting the boiler's hydraulic system.
Outlines the necessary steps and safety precautions for the boiler's electrical connection.
Explains the connection and function of optional remote controls and thermostats.
Describes the installation and function of the optional external temperature probe.
Details Immergas flue systems, their installation, and important safety considerations.
Provides data on resistance factors for flue system components.
Covers outdoor installation requirements and specific configurations.
Explains the process for internal installation with direct air intake.
Details the installation of horizontal concentric kits for air intake and flue exhaust.
Describes the installation of vertical concentric kits for air intake and flue exhaust.
Explains the installation of the separator kit for divided flue exhaust and air intake.
Details the installation of the C9 kit for direct air intake from the shaft.
Covers ducting operations for flue gas evacuation and Immergas ducting systems.
Guides on filling the heating system with water after installation.
Explains the operation and settings of the circulation pump.
Provides crucial safety precautions for operating and maintaining the boiler.
Details the annual maintenance procedures required to preserve boiler performance.
Explains the function of each button and indicator on the boiler's control panel.
Guides on operating the boiler in different modes (stand-by, summer, winter, solar).
Lists error codes and their corresponding causes and solutions for troubleshooting.
Describes how to access and view operating parameters via the information menu.
Highlights safety precautions for maintenance and initial checks.
Outlines the steps for commissioning the boiler and verifying its correct setup.
Details the essential annual checks and maintenance tasks for the boiler.
Provides a visual representation of the boiler's hydraulic circuits and components.
Shows the electrical connections and wiring layout of the boiler and its components.
Lists common issues, their potential causes, and troubleshooting steps.
Explains the procedure for adapting the boiler to different gas types.
Details how to calibrate the fan speed, especially after gas conversion or flue changes.
Guides on adjusting the air-gas ratio for optimal combustion.
Explains how to access and modify boiler operating parameters via the PCB.
Describes how to access and use special functions protected by a password.
Explains the function for performing thermal shock on new radiant panel systems.
Details the function for automatic deaeration of central heating systems.
Explains how to activate and use the flue function for testing.
Describes how to activate specific operating devices for verification.
Explains the function that forces the boiler to variable output for testing.
Details how to connect and configure the boiler with solar panels.
Explains the function that prevents the pump from blocking due to inactivity.
Describes the function that prevents the 3-way valve from blocking due to inactivity.
Explains the function that protects the system from freezing.
Provides step-by-step instructions for removing the boiler casing for maintenance.
Presents data on the boiler's heat output variations based on modulation.
Lists key parameters related to the boiler's combustion performance and efficiency.
Provides detailed technical specifications and performance data for the boiler models.
Explains how to interpret the information found on the boiler's data plate.
Lists technical parameters for combination boilers as per EU regulation.
Presents energy efficiency data and product information according to EU regulations.
Guides on filling package fiche for central heating and DHW systems.
To Next Page
