IMO Jaguar CUB - Table of Contents

xv
Table of Contents
Preface ............................................................i
 Safety precautions.................................................ii
 Precautions for use................................................x
How this manual is organized ................................ xiii
Chapter 1 BEFORE USING THE INVERTER ..... 1-1
1.1 Acceptance Inspection............................... 1-1
1.2 External View and Terminal Blocks ............ 1-2
1.3 Transportation............................................ 1-2
1.4 Storage Environment ................................. 1-3
1.4.1 Temporary storage ............................ 1-3
1.4.2 Long-term storage ............................. 1-3
Chapter 2 Mounting and Wiring of the Inverter.... 2-1
2.1 Operating Environment .............................. 2-1
2.2 Installing the Inverter.................................. 2-1
2.3 Wiring ....................................................... 2-2
2.3.1 Removing the Terminal Block (TB)
Covers............................................... 2-2
2.3.2 Terminal Arrangement and Screw
Specifications .................................... 2-3
2.3.3 Recommended Wire Sizes................ 2-4
2.3.4 Wiring Precautions ............................ 2-6
2.3.5 Wiring for Main Circuit Terminals and
Grounding Terminals ......................... 2-7
2.3.6 Replacing the Main Circuit Terminal
Block (TB) Cover ............................. 2-13
2.3.7 Wiring for Control Circuit Terminals . 2-14
2.3.8 Switching of SINK/SOURCE
(Jumper Switch) .............................. 2-20
2.3.9 Installing an RS485 Communications
Card (Option) .................................. 2-21
2.3.10 Replacing the Control Circuit Terminal
Block (TB) Cover ............................. 2-21
2.3.11 Cautions Relating to Harmonic
Component, Noise, and Leakage Current
2-22
Chapter 3 OPERATION USING THE KEYPAD ... 3-1
3.1 Keys, Potentiometer, and LED on the
Keypad....................................................... 3-1
3.2 Overview of Operation Modes.................... 3-2
3.2.1 Running Mode................................... 3-2
3.2.2 Programming Mode........................... 3-3
3.2.3 Alarm Mode....................................... 3-4
3.3 Operation in Running Mode ....................... 3-6
3.4 Setting the Function Codes--
"Data setting" ........................................... 3-12
3.5 Checking Changed Function Codes--
"Data checking"........................................ 3-15
3.6 Monitoring the Running Status--
"Drive monitoring" .................................... 3-16
3.7 Checking I/O Signal Status--
"I/O checking" .......................................... 3-20
3.8 Reading Maintenance
Information--"Maintenance information"... 3-23
3.9 Reading Alarm Information--
"Alarm information" .................................. 3-25
Chapter 4 RUNNING THE MOTOR .................... 4-1
4.1 Running the motor for a test ...................... 4-1
4.1.1 Inspection and Preparation prior to
the Operation .................................... 4-1
4.1.2 Turning on Power and Checking ....... 4-1
4.1.3 Preparation before running the motor
for a test--Setting function code data. 4-2
4.1.4 Test run ............................................. 4-3
4.2 Operation....................................................4-3
Chapter 5 FUNCTION CODES............................5-1
5.1 Function Code Tables.................................5-1
5.2 Overview of Function Codes ....................5-13
Chapter 6 TROUBLESHOOTING ........................6-1
6.1 Before Proceeding with Troubleshooting ....6-1
6.2 If no alarm code appears on the
LED monitor ...............................................6-3
6.2.1 Motor is running abnormally...............6-3
6.2.2 Problems with inverter settings ..........6-7
6.3 If an alarm code appears on the LED
monitor .......................................................6-9
Chapter 7 MAINTENANCE AND INSPECTION...7-1
7.1 Daily Inspection ..........................................7-1
7.2 Periodic Inspection .....................................7-1
7.3 Measurement of Electrical Amounts in
Main Circuit ................................................7-6
7.4 Insulation Test.............................................7-7
7.5 List of Periodical Replacement Parts..........7-8
7.6 Inquiries about Product and Guarantee......7-8
Chapter 8 SPECIFICATIONS ..............................8-1
8.1 Standard Models.........................................8-1
8.1.1 Three-phase 200 V Series .................8-1
8.1.2 Three-phase 400 V Series .................8-2
8.1.3 Single-phase 200 V Series ................8-3
8.2 Models Available on Order..........................8-4
8.2.1 EMC Filter Built-in Type .....................8-4
8.2.2 Braking Resistor Built-in Type............8-4
8.3 Common Specifications ..............................8-5
8.4 Terminal Specifications...............................8-7
8.4.1 Terminal Functions.............................8-7
8.4.2 Connection Diagram in Operation by
External Signal Inputs........................8-7
8.5 External Dimensions.....................................8-9
8.5.1 Standard Models and Models Available
on Order (Braking Resistor Built-in
Type)..................................................8-9
8.5.2 Models Available on Order (EMC Filter
Built-in Type).................................... 8-11
8.6 Protective Functions .................................8-13
Chapter 9 LIST OF PERIPHERAL EQUIPMENT
AND OPTIONS ...................................9-1
Chapter 10 COMPLIANCE WITH STANDARDS .10-1
10.1 Compliance with UL Standards and Canadian
Standards (cUL certification).....................10-1
10.1.1 General ............................................10-1
10.1.2 Considerations when using Jaguar CUB
in systems to be certified by UL and cUL
10-1
10.2 Compliance with European Standards......10-1
10.3 Compliance with EMC Standards .............10-2
10.3.1 General ............................................10-2
10.3.2 Recommended installation...............10-2
10.4 Harmonic Component Regulation
in the EU...................................................10-4
10.4.1 General comments...........................10-4
10.4.2 Compliance with the harmonic
component regulation ......................10-5