1500 Loader Series WHISPER
®
Loader
Replacement Parts
Item # Description
105977 14" dia. nylon filter (for 1500A units)
106026 14" dia. polyester felt filter (for 1500VP and 1500PLVPA units)
120065 Powder loader filter - 3 required (also for PL1250 units)
105990 14" gasket for all 14" filters
117362 Gasket between motor and cover (for all 1250A and 1500A units)
106008 60 psi filter regulator (for 1500A, 1500VP and 1500 PLVPA units)
106021 Vacuum motor with fan (for 1500A, 1500VP and 1500PLVPA units)
106053 Stationary fan to vacuum motor (for all 1250 and 1500 units)
106059 Rotating fan to vacuum motor (for all 1250 and 1500 units)
106407 Vent fan for vacuum motor (for all 1250 and 1500 units)
108830 Vent fan housing (for all 1250 and 1500 units)
106407 Vent Fan Blade, 2
7
/16” dia,
1
/4” Bore (for all 1250 and 1500 units)
106410 Armature to vacuum motor (for all 1250 and 1500 units)
105987 Brush kit (change brushes every 300 hours)
105970 Flapper only (for all 1500 units)
105978 Lid, latch and sound hood (for 1500VP and 1500PLVPA units)
106052 Check valve assembly (for 1500 PLVPA units)
119984 Proportional cylinder port plugs (for 1500PLVPA units)
149083 PLC Controller with standard program
149084 PLC Controller with VP program
149085 PLC controller with plvp program
119393 Pulse valve assembly (for 1500VP and 1500PLVPA units)
118589 Toggle switch, on/off (for all 1250 and 1500 units)
116286 Proximity switch (for all 1250 and 1500 units)
106056 Solenoid valve, 4-way (1250PLVPA and 1500PLVPA units)
106031 Motor housing connector, 5 pin (for 1500A units)
114245 Motor housing connector, 6 pin (for PL and VP units)
107656 Motor housing connector, 7 pin (for PLVPA units)
106014 Interconnect cord, 5 pin (for 1500A units)
106714 Interconnection Cord, Motor to Control Box, 7-Wire, 12ft. OAL (for 1500PLVP units)
109118 Interconnection Cord, Motor to Control Box, 6-Wire, 12ft. OAL
116050 Proximity cord (for 1250A and 1500A units)
105999 Control box, complete assembly (for 1500A units)
106023 Wand, Pick-up Probe, 36” Long, 1
1
/4” OD Tube, Aluminum
106033 1
1
/2" pick-up wand
108840 1
1
/2" I.D. loader hose
108207 1" to 2" worm gear clamp
137590 Retro Fit Kit 1250 - 1500 (to convert an old loader with an 070 pbc board to the PLC controller)
137591 Retro Fit Kit VP – PL (to convert an old loader with an 070 pbc board to the PLC controller)
137592 Retro Fit Kit PLVP (to convert an old loader with an 070 pbc board to the PLC controller)
NOTE: In 2006, IMS upgraded its loaders from boards to modules.
These modules are self-contained and when installed correctly
will eliminate dust and static wire issues.
© Copyright 2007 IMS Company. All rights reserved. An ISO 9001:2000 Registered Quality Company
25
To Next Page
Loading...
