66
En
HDMI
■ Audio TV Out
` Off
:
The audio is not output from the HDMI output.
` On:
The audio is output from the HDMI output.
This preference determines whether the incoming audio
signal is output from the HDMI output. You may want to
turn this preference on if your TV is connected to the
HDMI output and you want to listen to the audio from a
connected component through your TV’s speakers. Nor-
mally, this should be set to “Off”.
Note
• Listening mode cannot be changed when this setting is set to
“On” and the input source is not HDMI.
•If
“On” is selected and the audio can be output from the TV, the
AV controller will output no sound through its speakers. In this
case, “TV Sp On” appears on the display.
• When
“TV Control” is set to “On”, this setting is fixed to
“Auto”.
• With some TVs and input signals, no sound may be output even
when this setting is set to
“On” (➔ 67).
• When the “Audio TV Out” setting is set to
“On”, or “TV Con-
trol” is set to
“On” (➔ 67) and you’re listening through your
TV’s speakers (➔ 19), if you turn up the AV controller’s volume
control, the sound will be output by the AV controller’s front left
and right speakers. To stop the AV controller’s speakers produc-
ing sound, change the settings, change your TV’s settings, or
turn down the AV controller’s volume.
•If the “Monitor Out” setting is set to “Both(Main)” or
“Both(Sub)” (➔ 50) and if your TV connected to a priority out-
put cannot output the audio, the sound will be heard from AV
controller’s speakers.
■ Lip Sync
` Disable
:
HDMI lip sync disabled.
` Enable:
HDMI lip sync enabled.
The AV controller can be set to automatically correct any
delay between the video and the audio, based on the data
from the connected monitor.
Note
• This function works only if your HDMI-compatible TV supports
HDMI Lip Sync.
• You can check the amount of delay being applied by the HDMI
Lip Sync function on the A/V Sync screen.
•If the “Monitor Out” setting is set to “HDMI Main”,
“Both(Main)” or “Both” (➔ 50), the delay will be corrected in
accordance with the monitor connected to HDMI OUT MAIN.
On the other hand, if “HDMI Sub” or “Both(Sub)” is selected,
the delay will be corrected in accordance with the monitor con-
nected to HDMI OUT SUB.
■ HDMI Control(RIHD)
` Off
:
p disabled.
` On:
p enabled.
This function allows p-compatible components
connected via HDMI to be controlled with the AV control-
ler (➔ 107 to 108).
Note
• When set to “On” and close the menu, the name of connected
p-compatible components and “RIHD On” are dis-
played on the AV controller.
“Search…” → “(name)” → “RIHD On”
When the AV controller cannot receive the name of the compo-
nent, it is displayed as “Player*” or “Recorder*”, etc (“*”
means the number of two or more component).
•When an p-compatible component is connected to the
AV controller via the HDMI cable, the name of the connected
component is displayed on the AV controller display. For exam-
ple, while you are watching TV broadcasting, if you operate a
Blu-ray Disc/DVD player (being powered on) by the remote
control of the AV controller, the name of the Blu-ray Disc/DVD
player is displayed on the AV controller.
•Set to
“Off” when a connected piece of equipment is not com-
patible or it is unclear whether the equipment is compatible or
not.
• If movement is unnatural when set to
“On”, change the setting
to
“Off”.
• Refer to the connected component’s instruction manual for
details.
•The p control does not support HDMI OUT SUB. Use
HDMI OUT MAIN instead.
• When the source equipment is connected with the u connec-
tion, it may malfunction if “HDMI Control(RIHD)” is set to
“On”.
■ Audio Return Channel
` Off:
Select “Off” if you don’t want to use audio return
channel (ARC) function.
` Auto
:
The audio signal from your TV tuner can be sent to
the HDMI OUT MAIN of the AV controller.
Audio return channel (ARC) function enables an HDMI
(Audio Return Channel) capable TV to send the audio
stream to the HDMI OUT MAIN of the AV controller. To
use this function, you must select the TV/CD input selec-
tor and your TV must support ARC function.
Note
•The “Audio Return Channel” setting can be set only when the
“HDMI Control(RIHD)” setting is set to “On”.
• This setting is set to “Auto” automatically when the “HDMI
Control(RIHD)” is set to “On” first time.
To Next Page
Loading...
Need help?
General
