Integra Luxtec MLX Service Manual

4
M L X 3 0 0 W A T T X E N O N L I G H T S O U R C E
GENERAL WARNINGS
•TheusershouldcarefullystudytheOperation
and Service Manual before using the equipment
in a clinical environment. Instructions should be
followed, with special attention given to warnings,
controlsanduserspecications.TheManualshould
be available to the appropriate personnel.
•ThisManualcontainsinformationabouttheproper
procedures for preparing this product for its use
and care.
•Beforeeveryprocedure,carefullyinspectthelight
source to ensure it has been properly maintained
and cleaned, and that it is fully functional. DO NOT
use if inspection reveals any damage such as case
damage or loose connectors.
•Followtheinstructionsofothermanufacturer’s
equipment when used in conjunction with this
product.
•Toreducetheriskofreandelectricshock,donot
expose electrical equipment to moisture. When
cleaning, do not immerse any electrical device in
liquid.
•Donotuseorstoreliquidsonorabovethelight
source.
•SAFETYPRECAUTIONSMUSTALWAYSBE
EXERCISED WHEN USING ELECTRICAL
EQUIPMENT TO PREVENT OPERATOR/PATIENT
SHOCK, FIRE HAZARD OR EQUIPMENT
DAMAGE.
•Electricshockhazard.Ifunitisnotfunctioning
properly, DO NOT OPEN. Please refer to the
Repair and Return Section of this Manual.
•Allelectricalequipmentmustbeusedwithapproved
hospital grade power cords and power plugs
inserted properly into grounded AC power outlets.
•Thelightsourceshouldneverbeusedinocular
surgery or in a surgical procedure requiring direct
illumination of the eye.
•Usecarenottopointanyberopticcabledirectly
at the eye while operating the light source.
•Thelightsourceproduceshighintensitylight.
Thermal burns can result from improper use of the
lightsourceorfromthelightoutputoftheber
optic cable.
•Takeprecautionstoverifythattheberopticcable
is appropriately suited for the light source. Xenon
and other high illumination light sources. require
premiumberopticcablesinordertoachieve
optimal performance and prevent damage to the
bers,therebydiminishingthequalityofthelight
outputortheusefullifeofberopticcable.
•Takeprecautionsnottotouchordisconnectthe
cableendttingfromtheturretuntiltheLight
Source has been “shut down” for a period of time
andallowedtocool.Thecableendttingwill
remain hot immediately following shut down, which
can cause burns.
•Takeprecautionstonotplaceandrestahotcable
endttingand/orheadlightonapatientorallow
the system to come in contact with un-protected
hands or tissue. The entire system should be
allowed to cool following use. Failure to do so can
cause burns and/or tissue damage.
PRECAUTIONS
•ExplosionHazard.Donotuseinthepresenceof
ammableanesthetics,liquids,vapors,gasesordusts.
•Keepcoolingventandfansfreeofobstructions.
•FIREHAZARD:DONOTDRAPEORCOVERTHE
LIGHT SOURCE WHILE IT IS OPERATING.
•Whenlightsourceisnotinuse,turnoffthepower
or put the unit in stand-by mode.
•Ensurethattheberopticcablematchestheport
type to prevent damaging the optical components
of the light source. For user convenience, the light
source has a turret with labeled selectable ports.
•Donotusetheheadlightatdistancesoflessthan
10” (25cm).

Integra Luxtec MLX Specifications

General

Brand	Integra
Model	Luxtec MLX
Category	Medical Equipment
Language	English