To Next Page
J
James MillerSep 3, 2025
What to do if my Intergas Combi Compact HRE 24/18 Boiler displays sensor fault S1?
- CChristopher SmithSep 3, 2025
If your Intergas Boiler shows a sensor fault S1, check the wiring for any breaks and replace S1 if necessary.
What to do if my Intergas Combi Compact HRE 24/18 Boiler displays sensor fault S1?
If your Intergas Boiler shows a sensor fault S1, check the wiring for any breaks and replace S1 if necessary.
What to do if there is flame detection fault in Intergas Boiler?
If you're getting a flame detection fault on your Intergas Boiler, try these solutions: * Replace the ignition cable and spark plug cap. * Replace the ignition unit. * Replace the boiler controller.
Why is my Intergas Boiler's CH not reaching the set temperature?
If the central heating (CH) in your Intergas Boiler isn't reaching the set temperature, consider these steps: * Check and adjust the room thermostat setting to 0.1A if it's incorrect. * Increase the CH temperature if it's too low. Check the outside sensor for short circuiting and rectify if needed. * Increase the pump setting or replace the pump if it's not running correctly or the setting is too low. * Ensure there is circulation in the installation; at least 2 or 3 radiators must be open. * Adjust the power if the boiler power hasn't been correctly set for the installation (refer to setting maximum CH power). * De-scale or flush the heat exchanger on the CH side if there's no heat transfer due to lime scale or fouling.
Why does the hot water from my Intergas Combi Compact HRE 24/18 not reach temperature?
If your Intergas Boiler's hot water isn't reaching the desired temperature, consider the following: * Adjust the inlet assembly if the DHW flow is too high. * Set the hot water circuit depending on the desired temperature, if the temperature setting for the water circuit is too low. * Descale or flush the exchanger DHW side if there's no heat transfer due to lime scale or fouling in the heat exchanger DHW side.
Why is the burner resonating in my Intergas Combi Compact HRE 24/18 Boiler?
If your Intergas Boiler's burner is resonating, consider these potential causes: * The gas supply pressure may be too low. The house pressure switch may be faulty; contact the gas company. * There might be recirculation of combustion gasses; check the gas flue and the air supply. * The gas/air adjustment might not be correctly set; check the setting (refer to gas/air adjustment guidelines).
Why is my Intergas Boiler not producing hot water (DHW)?
If your Intergas Boiler is not providing hot water, consider the following: * Replace the flow switch if the DHW flow is less than 2.0 l/min. * Check the wiring according to the diagram if there's no current at the flow switch (5V DC). * Replace S3 if the burner isn't firing on DHW. * Refer to the 'burner does not ignite' section if the burner isn't igniting.
Why does my Intergas Combi Compact HRE 24/18 Boiler burner ignite noisily?
If your Intergas Boiler's burner ignites noisily, it could be due to several reasons: * The gas supply pressure might be too high. The house pressure switch may be faulty; contact the gas company. * The ignition electrode gap may be incorrect; check the ignition electrode gap. * The gas/air adjustment may not be correctly set; check the setting (refer to gas/air adjustment guidelines). * There might be a weak spark; the spark gap should be approximately 4.5 mm.
Why is there no heating (CH) in my Intergas Combi Compact HRE 24/18?
If your Intergas Boiler isn't providing heat, consider the following troubleshooting steps: * Replace the thermostat if it's faulty. * Check the wiring against the diagram. * Check the connector X4 if there's no current (24 V). * Replace the faulty manager. * Check the power supply at connector X2. * Replace the faulty pump if it's not running. * Replace sensor S1 or S2 if the burner isn't firing on CH. See fault code. * Refer to the 'burner does not ignite' section if the burner isn't igniting.
Highlights critical points for installers, including user instruction and benchmark compliance.
Lists essential checks for installers regarding user instruction, benchmark logbook, and gas safety.
Guides through unpacking, fitting condensate trap, and connecting flue pipes.
Details connecting the central heating system, including required components like drain taps.
Guides connecting the DHW installation and explains flow resistance and minimum pressure requirements.
Details electrical connections for thermostats, sensors, and mains power supply.
Provides specific wiring instructions for on/off, OpenTherm thermostats, and sensors.
Describes the concentric flue adapter, air supply, and approved flue products.
Guides through filling and venting the central heating and hot water systems.
Covers combustion checks, flue system integrity, and proceeding to operation.
Details the appliance startup procedure, pressure checks, and temperature differences.
Details procedures for checking gas supply pressure and performing initial boiler firing.
Explains direct operation of functions like on/off, DHW comfort, and resetting via the control panel.
Guides on accessing and adjusting parameters using the service code for various settings.
Guides on measuring flue gas O2/CO2 levels at maximum output for combustion analysis.
Details measuring flue gas O2/CO2 levels at minimum output for combustion analysis.
Explains how to adjust the gas-air ratio on minimum power using the adjustment screw.
Covers CO2 adjustment at minimum power and protection of adjustment screws.
Details how to set maximum CH supply temperature and DHW temperature.
Lists common fault codes, their display, and possible solutions for troubleshooting.
A checklist for competent persons to complete for boiler installation and commissioning compliance.
General| Model | Combi Compact HRE 24/18 |
|---|---|
| Category | Boiler |
| Efficiency | 93% |
| Weight | 32 kg |
| Boiler Type | Combi |
| Mounting | Wall Mounted |
| ERP Rating | A |
| Max. working pressure | 3 bar |
| Fuel | Natural Gas |
| Efficiency (%) | 93 |
