Interquartz Gemini IQ333 - Wireless Headset*, Handset Lifter* and OLI* Installation (* see note); Wireless Headset* EHS and OLI* Installation (*see note); Location; Wall Mounting

19
WIRELESS HEADSET*, HANDSET LIFTER* and OLI* INSTALLATION (* see note)
1. Plugthetelephone interfacecablesuppliedwiththeWirelessheadset(alsocalled“telephonecable”in
some Plantronics headset manuals) to the telephone socket on the headset base unit and to the IQ333
handset socket.
2. Connect the handset coiled cord according to the Headset manufacturer’s instructions
3. Install the Handset Lifter according to the manufacturer’s instructions
4. Connect OLI cable (optional) to the accessory Jack on the Handset Lifter.
Please refer to the connection diagrams (Fig 2) in this manual and on our website to see a visual guide to
the above steps and connections. If your headset is not one of those illustrated, please follow the general
informationinthesectionsentitled“HEADSETMICADJUSTCONTROL”and“HEADSETPOLARITYSWITCH”
tondadjustmentsneededtosuityourheadset.
*Note:itemsmarkedwith“
*
”notmanufacturedbyInterquartz
WIRELESS HEADSET* EHS and OLI* INSTALLATION (*see note)
1. Plugthetelephone interfacecablesuppliedwiththeWirelessheadset(alsocalled“telephonecable”in
some Plantronics headset manuals) to the telephone socket on the headset base unit and to the IQ333EHS
headset socket at the telephone’s rear.
2. ConnectoneendoftheInterquartzEHScable(suppliedwithIQ333EHS)totheAccessoryPort(otherwise
known as Handset Lifter Jack) of the Wireless base unit and connect the other end to the EHS port on the
left side of the IQ333EHS bottom casing.
3. Set Headset Polarity Switch according to the connection drawing (Fig 2).
4. Connect OLI cable (optional) to the OLI port on the left side of IQ333EHS.
*Note:itemsmarkedwith“*”notmanufacturedbyInterquartz
NOTE: The IQ333EHS’s coiled handset cord should remain plugged in to the telephone’s HANDSET socket. Do
not connect it to the base of the wireless headset.
Please refer to the connection diagrams (Fig 2) in this manual to see a visual guide to the above steps and
connections. If your headset is not one of those illustrated, please follow the general information in the sections
entitled“HEADSETMICADJUSTCONTROL”and“HEADSETPOLARITYSWITCH”tondadjustmentsneeded
to suit your headset.
LOCATION
The telephone should be placed on a desk, table or shelf where it is not likely to be pushed off. If the unit is
tobewallmounted,itshouldbeseatedsecurelyontheWALLMOUNTINGBRACKET.Avoidexcessiveheat,
damp, dust, direct sunlight, vibration, and other appliances or devices that may transmit or emit electrical or
electromagneticradiofrequencynoiseorsignals(e.g.computers,welders,pagers).Trytokeepthewireless
headset base unit separate from the telephone (as far away as the supplied cords comfortably allow).
WALL MOUNTING
1. Fit the WALL MOUNT BRACKET (optional, not supplied) to the wall and attach the WALL MOUNT BRACKET
to the underside of telephone (see Fig 3)
2. To enable the HANDSET to be supported in the cradle, follow the procedure shown in (Fig 3) to reverse the
HANDSET RETAINER
NOTE: The WALL MOUNT BRACKET and MODULAR WALL JACK illustrated in (Fig 4) are available from your
authorizedInterquartzdealerandcanbeorderedas"WallMountKitNo.3".