Intex PureSpa SJB-HS-20-1C Owner's Manual

299
A
S AVE THESE INSTRUCTIONS
(299IO) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 08/20/2018
English
Page 9
PRODUCT SPECIFICATIONS
SET UP
Inatable,portableabovegroundcord-connectedspawithpump,heater,waterjet,blower,controlpanel,
built-in hard water treatment, and sanitation system.
WARNING:
Riskofre:This product draws a minimum of 13 AMPS. Most household circuits
are 13 to 16 AMPS. If the circuit breaker trips, please check that no other appliances or other
large loads are on the same circuit as the spa. Never use an extension cord. Unfold the line
cord prior to use. Never place the plug on combustible materials.
Note:
the spa equipment features a complete grounding system that is also in contact with the spa water. It
is possible that a person may build up static electricity that discharges when touching the water. Regardless,
anyelectricshockexperiencedshouldbeinvestigatedbyaqualiedelectricianpriortouseofthespa.
Unplug the spa until the cause is determined and any corrective action completed.
Site preparation and requirements
• The spa can be installed indoor or outdoor. For household use only.
• Makesuretheareaiswaterresistant,level,atandfreeofsharpobjectsunderoraroundthespa.
• Provide a properly located grounded electrical outlet with a protection grade of IPX4 or higher to connect
the spa and allow easy access for periodic testing of the cord mounted RCD.
• Make sure there is enough clearance around the spa for full access to the spa equipment for maintenance
and/or service.
• The area shall facilitate draining purposes during long term spa storage. Check local and national
regulations regarding spa water disposal requirements.
• To reduce noise disturbance, do not install the spa in the immediate vicinity of vertical walls.
• The area shall be within reach of fresh water supply in compliance with local water regulations, and whose
parameters shall be adjusted according to the spa water chemistry and balance section of the manual
beforerstuseofthespa.
• Check your local laws and regulations regarding indoor and/or outdoor spa installation.
Additional requirements for indoor installation
• Makesuretheoorcansupportthefullweightofthelledspawiththemaximumnumberofoccupants.
Checkwithaqualiedcontractororastructuralengineertoverifythisrequirement.
• Makesuretheooriswaterresistantandnon-slipsurface.Donotinstallthespaoncarpetorother
materials that will be damaged by moisture, condensation.
• Donotinstallthespaindoorsonasecondoorabovenishedlivingspaceduetothepossibilityofwater
and humidity damage.
Voltage / Frequency / Phase 220 – 240 V / 50 Hz / 1 PH
Maximum seating capacity: 4 adults 6 adults
Water capacity: 210 gal (795 L) 290 gal (1098 L)
Inner/outer diameter: 59/79 in (150/201 cm) 66/86 in (168/218 cm)
Height: 28 in (71 cm)
Jet pump: 650 Watts 700 Watts
Bubble air blower: 800 Watts
Filterpumpowrate: 460 gal/hr (1,741 L/hr)
Heater power: 2,200 Watts
Temperature range: 20ºC – 40ºC (68ºF – 104ºF)
Temperature rise: 1.5-2.5ºC/hr (3ºF – 4.5ºF/hr) 1-2ºC/hr (2ºF – 3.5ºF/hr)
Number of Water Jet Nozzles: 4 6
Number of Bubble Jets: 120 140
Spa tub recommended working air pressure: 0.083 bar (1.2 psi)

Intex PureSpa SJB-HS-20-1C Specifications

General

Brand	Intex
Model	PureSpa SJB-HS-20-1C
Category	Swimming Pool
Language	English