Intova DUB User Manual

PHOTO MODE MENU
13
DUB
While in photo mode, press the MENU button to enter
menu selection screen. Use the UP or DOWN navigation
buttons to highlight a menu item and press OK button
to access and adjust or activate various photo functions.
1. RESOLUTION: sets the photo le size’s pixel dimensions. Choices are: 12M, 8M, 5M, 3M, 2M and VGA.
Factory default is 8 megapixel (3264x2448).
2. WHITE BALANCE: adjusts color balance for various lighting situations.
a) AUTO: normal exposure/factory default.
b) DAYLIGHT: adjusts imagery to cooler (blue/cyan) color balance for warm outdoor lighting.
c) CLOUDY: adjusts imagery to warmer color balance for scenes with cool outdoor lighting.
d) FLUORESCENT: adjusts imagery to warmer color balance for scenes with uorescent lighting.
e) TUNGSTEN: adjusts imagery to cooler (blue/cyan) color balance for scenes with warm
(red/yellow) indoor lighting.
3. IMAGE QUALITY: sets photo quality between SUPER FINE, FINE and NORMAL compression. Factory
default is SUPER FINE.
4. METERING: selects the general area in a scene that the cameras uses when estimating exposure.
CENTER mode uses an area towards the middle of the scene. MULTI mode uses the overall area in a
scene. SPOT uses a very concentrated area in the middle of the scene. Factory default is CENTER.
5. SHARPNESS: setting increases or decreases image sharpness. Select HARD to increase sharpness
and SOFT to decrease sharpness. Factory default is NORMAL.
6. ISO: adjusts the camera’s sensitivity to light. The default setting is AUTO. A higher ISO number will
result in a better exposure for video/photo and is useful in low light conditions. The choices are AUTO,
50, 100, 200, 400, 800, and 1600.
7. EXPOSURE: adjusts the brightness or darkness of the imagery between ±2 stops. Setting to positive
values will brighten exposure, while negative values will darken exposure. Factory default is 0.0.
8. STABILIZER: sets the electronic image stabilization to ON or OFF. Stabilizer function is only eective
to reduce very minor vibration that can cause motion blur when taking a photo. Factory default is ON.
9. AUTO REVIEW: sets the amount of time an image of the photo that was taken remains for viewing
on the LCD screen before returning to live view. Setting choices are OFF, 1 sec, 3 sec and 5 sec. Factory
default is OFF.
10. SELF-TIMER: sets time delay in seconds between pressing of SHUTTER button and taking of photo.
Factory default is OFF. To activate self-capture:
a. In PHOTO menu highlight “Self-Timer” and press OK button to enter function.
b. Select 2S (2 sec) or 10S (10 sec) and press OK button to conrm.
c. Press MENU button to exit menu and LCD screen should show self-timer icon.
d. Press SHUTTER button to start timer.
11. PHOTO BURST: sets photo mode at 3, 5, 10 continuos photos per shutter button press. Factory
default is OFF.
12. TIMELAPSE: sets the camera to record video clips with delays between each frame corresponding to
selected time interval in seconds or minutes. This produces a time lapse video without the need for post
production. Setting choices are OFF, 3 sec, 5 sec, 10 sec, 30 sec, 1 min and 3 min. Factory default is OFF.
13. TIMELAPSE DURATION: when timelapse function is activated this function can be accessed to set
the length of the timelapse video. Choices are OFF (Unlimited), 3 min, 5 min, 10 min, 15 min, 20 min,
30 min and 60 min. Factory default is OFF.
14. DATE STAMP: sets the date only or date and time on the video clip which is visible during playback.
Setting choices are OFF, DATE, and DATE/TIME. Factory default is OFF.
1
s0

Intova DUB Specifications

General

Brand	Intova
Model	DUB
Category	Action Cameras
Language	English