Need help?Do you have a question about the Invisio V60 and is the answer not in the manual?
General| Water Resistance | IP68 |
|---|---|
| Power Supply | External power supply or battery |
| Battery Type | Lithium-ion |
| Connectivity | Wired connections |
| Operating Temperature | -40°C to +55°C |
| Storage Temperature | -40°C to +70°C / -40°F to +158°F |
| Compatibility | Compatible with various communication platforms |
Describes the communication and hearing protection system's capabilities.
Steps to connect, power on, and transmit with the V60.
Procedure for turning off the V60 unit.
Advises on avoiding acoustic feedback and managing sound levels.
How to adjust hear-thru volume using the Mode Button.
Method to disable hear-thru functionality.
Procedure to turn hear-thru back on.
Action performed by a long press on the Mode Button.
Action performed by a short press on the Mode Button.
Details on Enhanced, Natural, and Comfort Hearing modes.
Advice on reducing noise exposure in vehicles.
Lists various transmission methods like PTT and Latching.
Explains how PTT buttons are dynamically assigned to COM ports.
Highlights impact of cable configurations on functionality.
Illustrates PTT assignment for single net radios.
Illustrates PTT assignment for dual net radios.
Notes on certain cables not utilizing PTT buttons.
Default audio routing configuration for received audio.
Tones indicate PTT press/release and volume changes.
COM1 supports dual net audio routing.
Procedure to swap audio routing between left and right ears.
Key combination to initiate audio swap.
Tones indicating audio swap and default states.
Describes swapped audio routing to COM ports.
Note on audio heard during transmission.
How to enable audio in both ears via key combination.
Key combination steps to activate both ears mode.
Audio tones for enabling and disabling both ears mode.
Intended use of both ears mode in high noise environments.
Compatibility of IntelliCable with both ears mode.
Note on audio reception during transmission.
Procedure to mute all radios by -20 dB via key combination.
Key combination steps to mute or unmute radios.
Audio tones indicating mute and unmute states.
Actions to exit the mute all radios mode.
Note on certain cables not supporting mute mode.
Select one audio focus, muting others by 20 dB.
Key combination steps to activate/deactivate monitoring.
Audio tones for focus, de-focus, and error states.
Specifies PTT buttons for COM ports in monitor mode.
Actions to exit the single radio monitor mode.
Error tone for no cable connection to COM port.
Enables an alternative duplex state on certain cables.
Key combination steps to activate alternative state.
Tones for state on/off and incompatible cables.
Specifies PTT buttons for COM ports in alternative state.
Most cables use Open Mic Mode as the alternative state.
Describes power sources for the V60 unit.
Explains how the V60 automatically starts when powered.
Warning tones heard when an incompatible cable is connected.
Specific audio tones for COM and headset cable errors.
Identifies incorrect IntelliCable settings or faulty cables.
Priority order for detecting multiple cable failures.
Steps to troubleshoot when the system does not power on.
Checks for bad audio transmission, including headset fit.
Troubleshooting steps for the hear-thru feature.
Advice to contact representative if issues persist.
Resets key combinations to the V60's original state.
Key combination sequence to perform a system reset.
Audio tone indicating successful system reset.
System reset does not alter the V60 firmware version.
Details on standard and available clips for the V60.
Information on using the 2 mm Hex Key for clip changes.
Clip can be rotated for different mounting directions.
Instructions for threading the Molle clip through webbing.
Advice on positioning cables to avoid hard bends.
Ensures secure fastening to prevent injury.
Do not thread cables through equipment to prevent abrasion.
How to remove connectors by pulling the connector, not the cable.
Ensure cables are fastened to avoid entanglement and stress.
Store in a protected area without excess weight to prevent damage.
Store in a dry, ventilated area with caps removed.
Rinse with fresh water if dirty or exposed to salt water.
General rules for V60 audio tones based on on/off.
Tones associated with hear-thru control and volume adjustments.
Tones for PTT operations and radio connection status.
Tones for power status and open mic mode.
Refers to battery pack manual for specific tones.
Definition of INVISIO Bone Conduction Microphone.
Microphone monitoring ambient audio situational awareness.
Push-to-talk function for 2-way radio communication.
Allows two-way communication, not simultaneously.
Allows simultaneous communication for all users.
Keeps the microphone on without continuous pressing.
Intelligent cable system for recognizing attached devices.
To Next Page