INVT Goodrive300-01A Series User Manual

INVT Goodrive300-01A Series

97 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

Table of Contents

Questions and Answers:

J
Jonathan CrossSep 2, 2025
How do I fix a motor autotuning fault on INVT Goodrive300-01A DC Drives?
- R
  Robert GordonSep 2, 2025
  If your INVT DC Drive is experiencing a motor autotuning fault, the motor capacity might not match the VFD capacity, so change the VFD model. The motor parameters might be set improperly; set the motor type and nameplate parameters correctly. Finally, if the deviation between the parameters obtained from autotuning and the standard parameter is huge, empty the motor load and identify again.
R
ronald51Aug 23, 2025
What to do if there is overcurrent at acceleration in INVT Goodrive300-01A?
- E
  Elaine ShortAug 23, 2025
  If your INVT DC Drive shows an overcurrent during acceleration, it could be due to several reasons. The acceleration or deceleration time might be too short, so try increasing it. Also, check if the grid voltage is too low or if the VFD power is insufficient, and correct if needed. Inspect the load for short circuits or stalls, and verify the output wiring. Lastly, ensure there isn't strong external interference affecting the drive.
J
Jessica KimSep 1, 2025
How to resolve 485 communication fault in INVT Goodrive300-01A DC Drives?
- S
  Steven GonzalesSep 1, 2025
  If you're experiencing a 485 communication fault with your INVT DC Drive, it could be due to several reasons. The baud rate may be set improperly, so set the proper baud rate. There might be a communication line fault, so check the wiring of the communication interface. The communication address could be incorrect, so set the correct communication address. Finally, strong interference could be affecting communication, so replace or change the wiring to improve anti-interference capacity.
J
Joseph AlexanderAug 31, 2025
What does external fault mean on INVT Goodrive300-01A?
- D
  David WilliamsAug 31, 2025
  If your INVT DC Drive displays an external fault, it means the S external fault input terminal is active. Check the external equipment input to resolve this issue.
C
christina39Aug 30, 2025
Why is the rectifier module overheating in my INVT Goodrive300-01A?
- T
  Timothy JuarezAug 30, 2025
  If the rectifier module in your INVT DC Drive is overheating, it could be due to a blocked air duct or a damaged fan. Ventilate the air duct or replace the fan. The ambient temperature may also be too high, so lower the ambient temperature. Finally, long-time overload running can cause overheating, so reduce the load or running time.
H
Holly TylerAug 29, 2025
What to do if there is phase loss on output side in INVT Goodrive300-01A?
- C
  Courtney JonesAug 29, 2025
  If you are experiencing a phase loss on the output side of your INVT DC Drive, it could be due to a phase loss output occurring to U, V, and W, or a serious 3PH imbalance in the load. Check the output wiring and also check the motor and cable for any issues.
C
Christina DelgadoAug 28, 2025
How to troubleshoot phase loss on input side of INVT Goodrive300-01A?
- M
  michelle62Aug 28, 2025
  If your INVT DC Drive reports a phase loss on the input side, it means there's likely a phase loss or fluctuation occurring to the input R, S, and T. First, check the input power supply. Also, check the installation wiring to ensure everything is properly connected.
W
William PowellAug 27, 2025
What causes VFD overload in INVT Goodrive300-01A DC Drives?
- J
  James ClarkAug 27, 2025
  If your INVT DC Drive is showing a VFD overload, it could be because the acceleration is too fast, so increase the acceleration time. Another cause could be that the motor was restarted too soon. To resolve this, restart the motor after it has completely stopped.
B
Brad MitchellAug 27, 2025
What causes motor overload in INVT Goodrive300-01A?
- D
  Daniel BlairAug 27, 2025
  If your INVT DC Drive indicates a motor overload, it could be due to several reasons. The grid voltage might be too low, so check the grid voltage. The rated motor current might be set improperly; reset it to the correct value. Alternatively, the motor might be stalling or experiencing load transients. In this case, check the load and adjust the torque boost quantity.
K
Kara DelgadoAug 26, 2025
Why am I getting a bus undervoltage fault on my INVT Goodrive300-01A DC Drives?
- H
  heidi84Aug 27, 2025
  If your INVT DC Drive shows a bus undervoltage fault, it is likely that the grid voltage is too low. Check the grid input power to ensure it is within the appropriate range.

INVT Goodrive300-01A Series Specifications

General

Brand	INVT
Model	Goodrive300-01A Series
Category	DC Drives
Language	English

Related product manuals

Preview: INVT Goodrive350 Series

INVT Goodrive350 Series

Preview: INVT Goodrive200A Series

INVT Goodrive200A Series

Preview: INVT Goodrive100-PV Series

INVT Goodrive100-PV Series

INVT GD20-011G-4

INVT GD20-1R5G-4

INVT GD20-055G-4

INVT GD20-030G-4

INVT GD20-0R4G-S2

INVT GD300-2R2G-4

INVT GD350-2R2G-4

INVT GD20-2R2G-S2

INVT GD350-7R5G-4