EasyManua.ls Logo

Jandy Versa-Plumb CV Series - User Manual

Jandy Versa-Plumb CV Series
20 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
H 029 1800C
I nstallation and
O peration M anual
J andy
®
C artridge
Pool Filters
C L and C V V ersa- Plumb
™
S eries Filters
W A RN I N G
FO R Y O U R S A FE T Y - T his produc t must b e installed and serv ic ed b y a professional pool/
spa serv ic e tec hnic ian. T he proc edures in this manual must b e followed ex ac tly . I mproper
installation and/or operation can create dangerous high pressure which can cause the lter
lid to b e b lown off, possib ly c ausing death, serious inj ury or property damage. I mproper
installation and/ or operation will v oid the warranty .
B efore installing this produc t, read and follow all warning notic es and instruc tions that
accompany this lter. Failure to follow warning notices and instructions may result in
property damage, serious inj ury , or death.
C L and C V V ersa- Plumb
™
I n st a l l a t i o n a n d O p e r a t i o n D a t a

Table of Contents

Questions and Answers

  • G
    Gregory DanielsAug 3, 2025
    Why is there low water flow in my Jandy Water Filtration System?
    • M
      Megan MoodyAug 3, 2025
      If your Jandy Water Filtration System experiences low water flow, it could be due to several reasons. Start by checking and cleaning the filter system strainer baskets and inspecting all connections between the pool intake and the pump for air leaks. Ensure the pool water level is above the pump inlet line and that the pump is primed by filling it with water at the basket and replacing the lid. Also, inspect all lines for debris or partially closed valves, and clean or replace the filter cartridges as needed. Other potential causes include blocked pump impeller vanes (requiring a technician), broken strainer baskets (replace them), or the pump operating under speed due to low voltage (requiring a technician or electrician).
  • T
    Tiffany JohnsonAug 9, 2025
    How to fix water that is not clear with Jandy Water Filtration Systems?
    • M
      Maria Lane PhDAug 9, 2025
      If the water in your pool is not clear when using a Jandy Water Filtration System, several factors could be at play. Start by checking and adjusting the disinfectant level and testing and adjusting the water chemistry. Increase the pump run time and clean the filter cartridges according to the instructions, replacing the cartridge if necessary. Also, adjust the filter time or water chemistry to address heavy bathing or dirt loads.
  • E
    Emily WolfAug 15, 2025
    What to do if there is high pressure on start-up of Jandy Water Filtration Systems?
    • S
      Sharon NelsonAug 16, 2025
      High pressure on start-up of your Jandy Water Filtration System can be caused by a few things. It could be due to a small eyeball fitting in the pool or spa; consider replacing it with a larger diameter fitting. Another cause might be a partially closed valve on the return line, so check and fully open all valves. The pump might be too large for the system, in which case you should check the pump and filter selection. Lastly, dirty filter cartridges can cause high pressure, so clean them as per the instructions.
  • X
    xdelgadoAug 21, 2025
    Why are the filter cycles short in my Jandy Water Filtration Systems?
    • L
      Leah ThomasAug 21, 2025
      Short filter cycles in your Jandy Water Filtration System can occur due to several reasons. It may be caused by the presence of algae clogging the filter, so check the disinfectant content. Incorrect water chemistry can also lead to this issue, so check the pH, total alkalinity, and TDS. Additionally, if the pump output exceeds the design flow rate of the filter, check the pump performance. Clean or replace the filter cartridge as per the instructions.
  • D
    Donna NielsenAug 27, 2025
    What causes dirt to return to pool with Jandy Water Filtration Systems?
    • C
      Cody BakerAug 27, 2025
      If dirt returns to the pool when using your Jandy Water Filtration System, it's likely due to a hole in the filter cartridge or o-rings seal inside the filter. Replace the filter cartridge according to the instructions and replace the o-ring.

Summary

Safety Information

1.1 Important Safety Warning

Crucial warnings about high pressure, potential injury, and voiding warranty during operation and testing.

1.2 General Safety Instructions

Essential guidelines for installers and owners regarding safe operation, maintenance, and servicing procedures.

Installation Instructions

3.1 Filter Location

3.4 Filter Plumbing

Details on safe plumbing practices, pressure relief valves, pipe sizing, and connecting unions for optimal flow.

3.5 Clamp Installation

Step-by-step guide for correctly installing and tightening the filter clamp ring for secure lid attachment.

Start-Up and Operation

Filter Disassembly and Assembly

Maintenance

6.3 Cleaning the Filter Cartridge

Troubleshooting

Troubleshooting Guide

Lists common pool filter problems, their possible causes, and recommended solutions for effective diagnosis.

LIMITED WARRANTY

Jandy Versa-Plumb CV Series Specifications

General IconGeneral
Maximum Operating Pressure50 psi
MaterialReinforced Thermoplastic
Union2" union
Inlet/Outlet Size2 in
Tank MaterialReinforced Thermoplastic
Valve MaterialReinforced thermoplastic

Related product manuals