EasyManua.ls Logo

Jandy Versa-Plumb CV460 - User Manual

Jandy Versa-Plumb CV460
20 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
H 029 1800C
I nstallation and
O peration M anual
J andy
®
C artridge
Pool Filters
C L and C V V ersa- Plumb
™
S eries Filters
W A RN I N G
FO R Y O U R S A FE T Y - T his produc t must b e installed and serv ic ed b y a professional pool/
spa serv ic e tec hnic ian. T he proc edures in this manual must b e followed ex ac tly . I mproper
installation and/or operation can create dangerous high pressure which can cause the lter
lid to b e b lown off, possib ly c ausing death, serious inj ury or property damage. I mproper
installation and/ or operation will v oid the warranty .
B efore installing this produc t, read and follow all warning notic es and instruc tions that
accompany this lter. Failure to follow warning notices and instructions may result in
property damage, serious inj ury , or death.
C L and C V V ersa- Plumb
™
I n st a l l a t i o n a n d O p e r a t i o n D a t a

Table of Contents

Questions and Answers

  • J
    Jerry AndersonAug 9, 2025
    Why is there low water flow in my Jandy Water Filtration System?
    • M
      michaelhuffAug 9, 2025
      If your Jandy Water Filtration System experiences low water flow, it could be due to several reasons. Start by checking and cleaning the filter system strainer baskets and inspecting all connections between the pool intake and the pump for air leaks. Ensure the pool water level is above the pump inlet line and that the pump is primed by filling it with water at the basket and replacing the lid. Also, inspect all lines for debris or partially closed valves, and clean or replace the filter cartridges as needed. Other potential causes include blocked pump impeller vanes (requiring a technician), broken strainer baskets (replace them), or the pump operating under speed due to low voltage (requiring a technician or electrician).
  • C
    Crystal RichardsAug 15, 2025
    How to fix water that is not clear with Jandy Water Filtration Systems?
    • J
      Julie GarciaAug 15, 2025
      If the water in your pool is not clear when using a Jandy Water Filtration System, several factors could be at play. Start by checking and adjusting the disinfectant level and testing and adjusting the water chemistry. Increase the pump run time and clean the filter cartridges according to the instructions, replacing the cartridge if necessary. Also, adjust the filter time or water chemistry to address heavy bathing or dirt loads.
  • W
    Wendy RandallAug 20, 2025
    What to do if there is high pressure on start-up of Jandy Water Filtration Systems?
    • M
      Monica DominguezAug 21, 2025
      High pressure on start-up of your Jandy Water Filtration System can be caused by a few things. It could be due to a small eyeball fitting in the pool or spa; consider replacing it with a larger diameter fitting. Another cause might be a partially closed valve on the return line, so check and fully open all valves. The pump might be too large for the system, in which case you should check the pump and filter selection. Lastly, dirty filter cartridges can cause high pressure, so clean them as per the instructions.
  • C
    Carly HoganAug 27, 2025
    Why are the filter cycles short in my Jandy Water Filtration Systems?
    • C
      christina86Aug 27, 2025
      Short filter cycles in your Jandy Water Filtration System can occur due to several reasons. It may be caused by the presence of algae clogging the filter, so check the disinfectant content. Incorrect water chemistry can also lead to this issue, so check the pH, total alkalinity, and TDS. Additionally, if the pump output exceeds the design flow rate of the filter, check the pump performance. Clean or replace the filter cartridge as per the instructions.
  • S
    shafferjamieSep 2, 2025
    What causes dirt to return to pool with Jandy Water Filtration Systems?
    • M
      Mallory LopezSep 2, 2025
      If dirt returns to the pool when using your Jandy Water Filtration System, it's likely due to a hole in the filter cartridge or o-rings seal inside the filter. Replace the filter cartridge according to the instructions and replace the o-ring.

Summary

Safety Information

Important Safety Warning

Critical warnings about operating pressure, air, and installation safety for pool equipment.

General Safety Instructions

Guidelines for installers and general safety practices for safe pool equipment operation.

Installation Instructions

Filter Location

Anchor Bracket Installation

Instructions for securely fastening the filter to the equipment pad to withstand wind.

Filter Plumbing

Clamp Installation

Step-by-step guide for correctly installing the filter tank clamp for safe operation.

Start-Up and Operation

Start-Up and Operation

Procedures for safely starting up and operating the filter system, including priming and pressure checks.

Filter Disassembly and Assembly

Filter Disassembly and Assembly

Maintenance

Pressure Gauge

Cleaning the Filter Cartridge

Detailed steps for removing, cleaning, and inspecting filter cartridges for optimal filtration.

Troubleshooting

Troubleshooting

Common problems, their possible causes, and solutions for the filter system to ensure proper function.

Parts List and Exploded View

Jandy CL and CV Cartridge Filter Parts List

Jandy CL and CV Filters Exploded View

Jandy Versa-Plumb CV460 Specifications

General IconGeneral
Filter TypeCartridge
Filter Area460 sq ft
Max Flow Rate150 GPM
TypeCartridge Filter
Maximum Operating Pressure50 psi
MaterialFiberglass
Maximum Operating Temperature104°F
Tank MaterialFiberglass

Related product manuals