How to prevent electrode sticking with my Jasic MIG 350P Welding System?
If the electrode is sticking during welding with your Jasic Welding System, it could be because the arc force current is too low. Increase the arc force current appropriately.
What to do if there is no output current when pushing the torch trigger on my Jasic MIG 350P Welding System?
If the torch trigger is pushed, wire feeder works and gas flows, but there is no output current on your Jasic Welding System, and the protection LED is off, it could be due to: * The earth cable not being well connected to the workpiece. Reconnect it. * The control cable of the wire feeder not being well connected. Reconnect it. * The wire feeder or welding torch failing. Repair the wire feeder or welding torch.
Why is the fan not working on my Jasic MIG 350P?
If your Jasic Welding System's fan isn't working correctly, it could be due to: * A loose 3-phase power cord. Reconnect the cord. * A phase failure. Address the phase failure. * Overly low mains voltage. Welding can continue once the voltage recovers.
Why is the welding current unstable on my Jasic MIG 350P Welding System?
If you're experiencing unstable welding current with your Jasic Welding System, consider the following: 1. Ensure the pressure arm on the wire feeder is properly adjusted. 2. Verify that the drive roll matches the welding wire you are using. 3. Check the contact tip of the welding torch for wear and replace if necessary. 4. Inspect the guide tube in the torch and replace if worn. 5. Ensure you are using good quality welding wire.
What does error “Err 003” mean on my Jasic Welding System?
If your Jasic Welding System displays “Err 003”, there might be an issue with the air/water cooling switch position or a failure in the water circuit. Ensure the air cooling/water cooling switch is in the correct position. If it's a water circuit issue, resolve the water circuit failure.
What does it mean when my Jasic MIG 350P Welding System displays “Err 000”?
If your Jasic Welding System displays “Err 000”, it indicates an overcurrent or damage to power components. Try restarting the machine. If the problem persists, contact the service center.
What to do if my Jasic MIG 350P displays “Err 002”?
If your Jasic Welding System shows “Err 002”, it indicates overheating protection has been activated. Allow the machine to cool down, and it should recover automatically.
General| Output Current Range | 50-350 A |
|---|---|
| Duty Cycle | 60% at 350 A |
| Protection Class | IP21S |
| Insulation Class | F |
| Efficiency | 85% |
| Power Factor | 0.93 |
| Input Voltage | 3 Phase 400V |
| Wire Diameter | 0.8-1.2 mm |
| Wire Feed Speed | 1.5 - 18 m/min |
Comprehensive safety guidelines covering training, electric shock, smoke, arc radiation, fire, hot workpiece, and noise.
Details model designation, technical overview, and key features of the inverter welder.
Lists welding modes, base metals, gases, and wire types supported by the machine.
Specifies technical data and adjustable functional parameters for MMA and MIG/MAG welding.
Identifies and labels the main components of the welding machine's front and back panels.
Explains various symbols used on the front panel, back panel, and nameplate.
Provides an overview of the main control panel interface, including displays and selection zones.
Details selection zones for welding modes, base metal, shielding gas, and wire types.
Explains selection of process parameters like pre-flow, upslope, peak, base, downslope, crater, and post-flow.
Covers current/voltage parameter selection, operation modes, and the adjustment knob.
Explains gas-check functionality and channel management for saving parameters.
Recommended steps for operating the control panel for welding tasks.
Details adjustable parameters for MMA welding and their operation.
Lists and explains adjustable parameters for standard MIG/MAG welding.
Details adjustable parameters specific to pulsed MIG/MAG welding.
Explains unique parameters for double pulse MIG/MAG welding.
Guide to selecting different MIG/MAG operation modes and trigger operations.
Important safety precautions and warnings for operating and handling the welding machine.
Procedures for cleaning, checking connections, and general upkeep of the welding machine.
Common issues, causes, and solutions for the welding machine.
Specific troubleshooting for MMA and MIG/MAG welding issues.
Reference to the machine's internal wiring diagram provided in the appendix.
Information on manual applicability to models and potential updates.
To Next Page
