Jet 54A - User Manual

3
GB - ENGLISH
Operating Instructions
Dear Customer,
Many thanks for the confidence you have shown in us with the purchase of your new JET-machine. This manual has been
prepared for the owner and operators of a JET 54A/60A surface planer to promote safety during installation, operation and
maintenance procedures. Please read and understand the information contained in these operating instructions and the
accompanying documents. To obtain maximum life and efficiency from your machine, and to use it safely, read this manual
thoroughly and follow instructions carefully.
…Table of Contents
1. Declaration of conformity
2. Warranty
3. Safety
Authorized use
General safety notes
Remaining hazards
4. Machine specifications
Technical data
Noise emission
Dust emission
Contents of delivery
5. Transport and start up
Transport and installation
Assembly
Mains connection
Dust connection
Starting operation
6. Machine operation
7. Changing the knives
8. Maintenance and adjustment
9. Troubleshooting
10. Environmental protection
11. Available accessories
12. „safe operation” (appendix A)
1. Declaration of conformity
On our own responsibility we hereby
declare that this product complies with
the regulations* listed on page 2.
Designed in consideration with the
standards**. CE type examination***
performed by****.
2. Warranty
The Seller guarantees that the
supplied product is free from material
defects and manufacturing faults. This
warranty does not cover any defects
which are caused, either directly or
indirectly, by incorrect use,
carelessness, accidental damage,
repair, inadequate maintenance or
cleaning and normal wear and tear.
Guarantee and/or warranty claims
must be made within twelve months
from the date of purchase (date of
invoice). Any further claims shall be
excluded.
This warranty includes all guarantee
obligations of the Seller and replaces
all previous declarations and
agreements concerning warranties.
The warranty period is valid for eight
hours of daily use. If this is exceeded,
the warranty period shall be reduced
in proportion to the excess use, but to
no less than three months.
Returning rejected goods requires the
prior express consent of the Seller and
is at the Buyer’s risk and expense.
Further warranty details can be found
in the General Terms and Conditions
(GTC). The GTC can be viewed at
www.jettools.com or can be sent by
post upon request.
The Seller reserves the right to make
changes to the product and
accessories at any time.
3. Safety
3.1 Authorized use
This machine is designed for planing
wood, and wood derived materials.
Machining of other materials is not
permitted and may be carried out in
specific cases only after consulting
with the manufacturer.
The workpiece must allow to safely be
loaded, supported and guided.
With the jointer fence tilted forward
the following conditions must be
met:
The workpiece must safely be
supported and guided.
The workpiece must be higher than
the fence.
Only jointing operations are allowed.
The proper use also includes
compliance with the operating and
maintenance instructions given in this
manual.
The machine must be operated only
by persons familiar with its operation,
maintenance and repair and who are
familiar with its hazards.
The required minimum age must be
observed
The machine must only be used in a
technically perfect condition
When working on the machine, all
safety mechanisms and covers must
be mounted.
In addition to the safety requirements
contained in this operating instructions
and your country’s applicable
regulations, you should observe the
generally recognized technical rules
concerning the operation of
woodworking machines.
Any other use exceeds authorization.
In the event of unauthorized use of the
machine, the manufacturer renounces
all liability and the responsibility is
transferred exclusively to the operator.
3.2 General safety notes
Woodworking machines can be
dangerous if not used properly.
Therefore the appropriate general
technical rules as well as the following
notes must be observed.
Read and understand the entire
instruction manual before attempting
assembly or operation.

Summary

Declaration of Conformity

Warranty

Safety

Authorized Use

Defines permitted use and user qualifications for the machine.

General Safety Notes

Essential safety precautions for operating the machine safely.

Remaining Hazards

Potential risks that may still exist even with proper use.

Machine Specifications

Technical Data

Detailed technical specifications for the 54A and 60A models.

Noise Emission

Information on acoustic pressure and power levels.

Dust Emission

Details on dust extraction performance and workplace limits.

Content of Delivery

List of items included with the machine upon purchase.

Transport and Start Up

Transport and Installation

Guidelines for safely moving and setting up the machine.

Assembly

Step-by-step instructions for assembling machine components.

Mains Connection

Electrical connection requirements and safety measures.

Dust Connection

Instructions for connecting the dust extraction system.

Starting Operation

Procedure for starting and stopping the machine.

Machine Operation

Correct Operating Position

Recommended body posture for safe and effective operation.

Workpiece Handling

Safe techniques for guiding workpieces during operation.

Changing Cutter Knives

Operating Notes

Important tips and precautions for changing cutter knives.

Authorized Use Reference

Reference to appendix A for specific safe operations.

Maintenance and Inspection

General Notes

Precautions to take before performing any maintenance.

Reset Fence and Cutter Block Guard

Procedures for resetting the fence and cutter block guard.

Troubleshooting

Motor Doesnt Start

Diagnosing and fixing issues when the motor fails to start.

Machine Vibrates Excessively

Identifying and resolving causes of excessive machine vibration.

Cutting Surfaces is Bad

Troubleshooting common problems with surface finish quality.

Snipe

Addressing and correcting snipe on workpieces.

Table Difficult to Adjust

Resolving issues related to table adjustment.

Poor Machining Power

Troubleshooting causes of reduced machining power.

Environmental Protection

Available Accessories

Safe Operation

Jet 54A Specifications

General

Voltage	230V
Cutterhead Speed	5000 RPM
Cuts Per Minute	20, 000
Maximum Depth of Cut	1/8 inch
Maximum Cutting Width	13 inches
Maximum Cutting Height	6 inches
Minimum Cutting Length	10 inches
Feed Rate	26 FPM
Type	Planer
Phase	Single