5
Wood chips and sawdust can be
health hazards. Be sure to wear
personal protection gear such as
safety goggles ear- and dust
protection.
Use a suitable dust exhaust system.
The use of incorrect mains supply or a
damaged power cord can lead to
injuries caused by electricity.
The type and condition of the
sawblade is important in keeping the
noise level as low as possible.
This does not negate the fact that
extra safety equipment such as ear
protection must be used.
4. Machine specifications
4.1 Technical data
Machine Table 800x350 mm
Right extension table 800x270 mm
Rear extension table 415x350mm
Sliding table size 1000x255 mm
Max. travel of sliding table 660 mm
Max. length of cut 610 mm
Sawblade diameter max 250 mm
Blade bore diameter 30 mm
Blade speed n
0
4000 rpm
Cutting height at 90°/45° 80/54 mm
Tilting range of blade 90°- 45°
Max. width of rip cut 610 mm
Dust port diameter 100mm
Weight 145 kg
Mains 230V ~1/N/PE 50Hz
Motor output power 1,5kW (2HP) S1
Reference current 11 A
Extension cord (H07RN-F): 3x1,5mm²
Installation fuse protection 16A
Mains 400V ~3/PE 50Hz
Motor output power 1,5 kW (2 HP) S1
Reference current 4.7 A
Extension cord (H07RN-F): 4x1,5mm²
Installation fuse protection 16A
4.2 Noise emission
Determined according to EN 1870-1
(Inspection tolerance 4 dB)
Workpiece plywood 16mm:
Acoustic power level
(according to EN ISO 3746):
Idling LwA 98,2 dB (A)
Operating LwA 101,8 dB (A)
Acoustic pressure level
(according to EN ISO 11202):
Idling LpA 84,2 dB (A)
Operating LpA 88,5 dB (A)
The specified values are emission
levels and are not necessarily to be
seen as safe operating levels.
This information is intended to allow
the user to make a better estimation of
the hazards and risks involved.
4.3 Dust emission
The circular saw has been dust
emission evaluated.
At an air velocity of 20m/sec on the
dust port dia. 100mm:
Vacuum pressure 850Pa
Volume flow 565 m³/h
The TRK-value of 2 mg/m
3
is not
exceeded.
4.4 Content of delivery
Machine stand
Sliding table
Crosscut table
Crosscut fence
Telescopic arm
Rare extension table
Right extension table
Rip fence with dual fence profile
Rip fence support bar
Saw guard
Sawblade 250mm
Dust connection hose and Y-adapter
Hose tye
Push stick
Operating tools
Assembly bag
Operating manual
Spare parts list
4.5 Description of machine
Fig 1
A…...Crosscut fence
B…..Pull out lock knob
C….Crosscut stop
D…..Crosscut table
E…..Sliding table
F…..Raving knife
G…..Saw guard
H….Dust connection hose
I…..Rip fence
J…...Telescopic arm
K….Front cabinet cover
L….On/ Off switch
M….Sliding table lock
N….Blade rise handwheel
O….Blade tilt lock
P….Blade tilt handwheel
Q….Rip fence micro adjustment
5. Transport and start up
5.1 Transport and installation
For transport to the desired location
use a forklift or hand trolley. Make
sure the machine does not tip or fall
off during transport.
The machine is designed to operate in
closed rooms and must be placed
stable on firm and levelled ground.
The machine must be levelled in both
directions to assure good sliding
motion of the sliding table.
If possible, the machine must be
placed on rubber plates which act as
shock absorbers and reduce the noise
level.
For packing reasons the machine is
not completely assembled.
5.2 Assembly
If you notice any transport damage
while unpacking, notify your supplier
immediately. Do not operate the
machine!
Dispose of the packing in an
environmentally friendly manner.
Clean all rust protected surfaces with
a mild solvent.
Mounting machine stand:
Attach the side panels to the front and
rear panel with the supplied bolts, flat
washers and nuts.
Attach the 4 rubber pads.
To Next Page
Loading...
