Why JLA Washer won't start?
If your JLA washer isn't starting, here are a few things to check: * Ensure the power cord is fully plugged into the electrical outlet. * Check the laundry room's fuse or circuit breaker. * Verify that the controls are correctly set. * Press the START keypad. * Make sure the loading door is closed tightly. * Insert coin(s) or card. * Ensure the door latch is properly adjusted relative to the door lock.
What to do if JLA 98 won’t fill?
If your JLA washer isn't filling, try the following: * Ensure the power cord is fully plugged into the electrical outlet. * Check the laundry room's fuse or circuit breaker. * Verify that the controls are correctly set. * Press the START keypad. * Make sure the loading door is closed tightly. * Ensure both hot and cold water faucets are turned on. * Check that the fill hoses are not kinked or twisted. * Clean the screens in the water mixing valve and the filter screens located at the faucet end of the fill hoses.
How to fix JLA 98 Washer that won’t drain?
If your JLA washer isn’t draining, try these steps: * Ensure the drain hose isn't kinked or twisted. * Make sure the drain hose isn't clogged. * Check that the drain receptacle isn't clogged. * The foreign object trap in the pump may be clogged; clean the trap.
Why is my JLA 98 leaking water?
If your JLA washer is leaking water, here are some things to inspect: * Check that the fill hoses are properly installed on the faucets and the washer’s water mixing valve. * Assess the condition of the fill hoses, replacing them every five years. * Ensure the drain receptacle isn't clogged. * Check the laundry room plumbing. * Inspect the rubber door gasket for tears or holes. * If the laundry load may be oversudsing, make sure you are using low-sudsing, high efficiency (HE) detergent. * If the laundry load may be overloaded, make sure you are using proper load sizes. * Ensure the outside perimeter of the door glass where the seal contacts the glass is clean.
What to do if JLA Washer won’t spin or tumble?
If your JLA washer isn't spinning or tumbling, consider the following: * Ensure the power cord is fully plugged into the electrical outlet. * Check the laundry room fuse or circuit breaker. * Verify that the controls are correctly set. * Press the START keypad. * Make sure that the loading door is closed tightly. * If the drive belt is broken, call the service person. * The foreign object trap in the pump may be clogged; clean the trap. Refer to the Maintenance section.
Why JLA 98 Washer stops or pauses during cycle?
Pauses are part of the JLA washer’s normal operation. Check the laundry room fuse or circuit breaker. An unbalanced wash load may cause the washer to stop and then restart spin automatically.
How to reduce soap suds in JLA 98?
To reduce excessive soap suds in your JLA washer: * Make sure you are using low-sudsing, high efficiency (HE) detergent. * Ensure you're using the amount of detergent recommended on the detergent’s label. If using non-HE detergent, use only 1/2 of the detergent manufacturer's recommended amount. * Make sure you are using proper load sizes, as overloading can cause oversudsing.
How to stop JLA 98 Washer from vibrating or moving?
To minimize vibration or movement in your JLA washer: * Make sure the washer is level, as uneven leveling can cause vibration. * Ensure the washer is installed on a solid, sturdy, and level floor. Avoid installing it on carpeting, soft tile, a platform, or other weakly supported structures. * Make sure rubber feet are installed on all four leveling legs.
Why is my JLA 98 Washer so noisy?
If your JLA washer is making noise, make sure the washer is level, as uneven leveling can cause vibration. Also, some sounds may be a part of normal operation for a frontload washer, such as clicking noise when door locks and clicking noise from balance ring during agitate part of cycle.
Why is the load too wet after washing in my JLA Washer?
If the load is too wet after washing in your JLA washer: * Redistribute the load if it may be unbalanced. * If the load is too small, add items to make a full load.
Crucial safety precautions and warnings for operating the washing machine safely.
Provides the recommended order for performing installation tasks correctly.
Guide for electrical hookup for washers equipped with a heater element.
Wiring instructions for connecting to a 230V single-phase electrical supply.
Wiring diagram and steps for a 400V 3-phase WYE power connection.
Wiring diagram and steps for a 230V 3-phase DELTA power connection.
Guide for electrical hookup for washers not equipped with a heater.
Procedures to ensure the washer is correctly positioned and level for stable operation.
Final steps for connecting the washer to the main electrical supply.
Specifications for voltage, frequency, and amperage needed for the washer.
Critical safety guidelines for proper electrical grounding connections.
How to select fabric types and wash temperatures using the control panel.
Lists common washer problems and provides potential causes and solutions.
To Next Page
General