JRC JMR-611 - Page 75

To Next Page

To Previous Page

3.5 GENERAL OPERATIONS





3-21

Changing Motion Mode of Trails (Trails mode)

Procedures 1 Place the cursor over the position at the lower left as following figure.

Press [ENTER] key.

The motion mode of trails is switched to true or relative.

Land

Ship

Trails

Land

Ship

Trails

True Motion Trails

Relative Motion Trails

Main Page

Preface3
Before Operation4
Precautions5
Glossary18
Table of Contents20
General and Equipment Composition27
Foreword29
Function of this System29
Features30
Configuration31
Exterior Drawings32
General System Diagrams36
Names and Functions of Control Panel Switches and Functions of Software Buttons37
Names and Functions of Control Panel Switches40
Menu List43
Names and Functions of On-Sceen Controls49
Basic Operation53
Flow Operation55
Power on and Start the System56
Observe and Adjust Video57
Acquire and Measure Data57
End the Operation and Stop the System58
Basic Menu Operation59
Preparation61
Adjust Display Brilliance [Brill]61
Adjust Operation Panel Brilliance [Panel]61
Switch Day/Night Mode [Day/Night]61
Adjust Brilliance of Information on Radar Display (Brilliance Setting)62
Adjust Sound Volume (Buzzer Volume)62
Reset Alarm Buzzer [Alarm Ack]63
Set Display Color63
Basic Operations64
Start Transmission [Tx]64
Stop Transmission [Stby]64
Change Range (Observation Range Scale) [+Range-]3-1064
Tune65
Control Sensitivity [Gain]66
Sea Clutter Suppression [Sea]66
Rain/Snow Clutter Suppression [Rain]67
Interference Rejection [Ir]67
Hide/Display Range Rings [Rangge Rings]68
Hide Ship's Heading Line (Hl Off)68
Sea State (Sea State)69
General Operations70
Move Cross Cursor Mark by Trackball70
Use Ebls (Electronic Bearing Lines) [Ebl1/Ebl2]70
Use Vrms (Variable Range Markers) [Vrm1/Vrm2]72
Use P-Lines (Parallel Index Lines) [P-Line]73
Move Own Ship's Display Position [Off Cent]74
Display Other Ships' Trails [Trails]74
Display Own Vector [Own Vect]76
Own Mark77
Time Setting78
Change the Unit of "Rate of Turn80
Expansion80
Stc Curve81
Display User Map82
Create User Map(Mark/Line)82
Correct Position on User Map (Shift)85
Correct Position on User Map (Shift Clear)85
Set User Map Display (Mark Display Setting)86
Operate User Map File (File Operations)96
Screen Capture100
Screen Capture Setting (Select Card Slot)100
Screen Capture Setting (Save File)101
Screen Capture Setting (Erase File)101
Screen Capture Setting (Capture Mode)102
Screen Capture Setting (Auto Capture Interval)102
Screen Capture Setting (Auto File Erase)103
User Setting104
User Setting (Load User Setting)104
User Setting (Save User Setting)105
User Setting (Erase User Setting)105
Format Card106
Ais Function107
Vessel Name List107
Vessel Information108
Display the Vessel Names on the Screen108
Ais Setting Menu109
Ais Symbol115
Measurement of Range and Bearing117
Measurement by Trackball119
True and False Echoes on Display123
Radar Wave with the Horizon125
Strength of Reflection from the Target127
Sea Clutters128
False Echoes130
Display of Radar Transponder (Sart)133
Maintenance135
Routine Maintenance137
Maintenance on each Unit138
Scanner Unit Nke-387138
Displayunit(Alpha-Screen)141
Trouble Shooting143
Fault Finding147
Trouble Shooting149
Replacement of Major Parts151
After-Sales Service155
Disposal161
Disposal of the Unit161
Disposal of Used Batteries162
Disposal of Used Magnetron163
Specifications165
Jmr-611 Type Radar167
Scanner(Nke-387)168
Scanner (Nke-387)168
Control Unit(Ncm-994)169
Input Signal170
Output Signal171
Standard Equipment Composition171
Distance between Units171
Appendix173
How to Insert and Remove a Card175

JRC JMR-611 - Page 75

Table of Contents

Related product manuals