−22 −
Input function list
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Abbreviation
This function works as the input signal of material edge sensor.
Rotation by pedal is prohibited.
Output of thread trimming is prohibited.
This function works as low speed switch for standing sewing machine.
This function works as high speed switch for standing sewing machine.
UP stop motion is performed when switch is pressed during
DOWN stop.
Brake stop motion by reverse revolution is performed at specified
angle when switch is pressed during DOWN stop
Rotation is prohibited.
This function works as input signal of thread trimmer knife sensor.
Every time the switch is pressed, cancel or addition of reverse
feed stitching at start or end is performed.
Every time the switch is pressed, alternate vertical amount
change output is inversed.
Alternate vertical amount change output is performed as long
as the switch is pressed.
Function
code
nop
HS
bHS
Ebt
TSW
FL
oHS
SEbt
PnFL
Ed
LinH
TinH
LSSW
HSSW
USW
rSW
SFSW
MES
AUbT
vErT
vSW
No function
Needle up / down compensating
stitching
Back compensating stitching
Function of canceling once reverse
feed stitching at the end of sewing
Thread trimming function
Presser foot lifting function
One stitch compensating stitching
Function of cancel of reverse feed
stitching at start/end
Presser lifting function when pedal
is neutral
Material edge sensor input
Function of prohibiting depressing
front part of pedal
Function of prohibiting thread
trimming output
Low speed command input
High speed command input
Needle lifting function
Reverse revolution to lift needle
function
Safety switch input
Thread trimmer knife sensor input
Cancel of automatic reverse feed
stitching/input of addition switch
Alternate vertical amount change
panel switch input
Alternate vertical amount change
knee switch input
Function item
(Standard setting)
Every time the switch is pressed, normal feed stitching by half
stitch is performed. (Same operation as that of up / down
compensating stitching switch on the panel.)
Reverse feed stitching is performed at low speed while the
switch is held pressing. (It is effective only when constant
dimension sewing pattern is selected with the CP-160.)
By depressing the back part of the pedal after pressing the
switch, operation of reverse feed stitching is canceled once.
This function is actuated as the thread trimming switch.
This function is actuated as the foot lifter switch.
Every time the switch is pressed, one stitch stitching operation
is executed.
By operating the optional switch, ineffective/effective can be
alternately changed over.
Every time the switch is pressed, the function whether
automatically lifting the presser foot when the pedal is neutral
or not can be selected.
Remarks
Output function list
nop
TrM
WP
TL
FL
bT
Ebt
SEbt
AUbt
vErT
SSTA
Abbreviation
Function
code
Function item
Remarks
0
1
2
3
4
5
6
7
8
9
10
No function
Thread trimming output
Thread wiper output
Thread release output
Presser lifter output
Reverse feed stitching output
EBT cancel monitor output
Reverse feed stitching at start/
end cancel monitor output
Automatic reverse feed stitching
cancel/addition monitor output
Alternate vertical amount change
(monitor) output
Sewing machine stop state output
(Standard setting) *
Output of thread trimming signal *
Output of thread wiper signal *
Output of thread release signal *
Output of presser lifting signal *
Output of reverse feed stitching signal *
State of one time cancel of reverse feed stitching at end function
is output.
State of cancel of reverse feed stitching at start/end is output.
State of cancel or addition of automatic reverse feed stitching is
output.
Output of alternate vertical amount change signal
Sewing machine stop state is output.
* Magnet output does not work when they are used as optional.
(Caution) Note that the voltage used in output function should not exceed the voltage set with W1 and W2.
To Next Page
Loading...
Need help?
General
