JUKI SC-810 - 4. Function setting list

– 16 –
*
Do not change the set values with asterisk (*) mark as they are functions for maintenance. If the standard set value set at the
time of delivery is changed, it is in danger of causing the machine to be broken or the performance to be deteriorated.
If it is necessary to change the set value, please purchase the Engineer’s Manual and follow the instructions.
(Descriptions of setting in this list are the standard values at the time of delivery of DDL-9000A.)
However, contents of function setting are subject to change for improvement of function and performance without notice.
4. Function setting list
No
Item Description
Setting range
Indication of function setting Ref. page
1
Soft start
function
The number of stitches to be sewn at a low speed when the soft-
start function is used at the start of sewing.
0 : Soft-start function is not operative.
0 to 9
(Stitches)
1 0
19
5
Flicker reducing
function
Flicker reducing function (If the hand lamp ickers).
0 : Flicker reducing function is not operative.
1 : Less effective
/
3 : Highly effective
0 to 3
5 0
19
6
Bobbin thread
counting
function
Bobbin thread counting function
0 : Bobbin thread counting function is not operative.
1 : Bobbin thread counting function is operative.
0/1
6 1
19
7
Unit of bobbin
thread counting
down
Unit of bobbin thread counting down
0 : Count/10 stitches
1 : Count/15 stitches
2 : Count/20 stitches
0 to 2
7 0
*
8
Number of
rotation of
reverse feed
stitching
Sewing speed of reverse feed stitching
150 to 3,000
(r.p.m.)
8 1 9 0 0
9
Thread
trimming
prohibiting
function
Thread trimming prohibiting function (used in case of without panel).
0 : Thread trimming prohibiting function is not operative.
1 : Thread trimming is prohibited.
(Output of solenoid is prohibited. : Thread trimmer and wiper)
0/1
9 0
19
10
Setting of
needle bar stop
position when
the sewing
machine stops.
Position of needle bar is specified when the sewing machine
stops.
0 : Predetermined lowest position
1 : Predetermined highest position
0/1
1 0 0
19
11
Click sound
of key switch
mounted on
PSC
Click sound of key switch mounted on PSC is specied.
0 : Click is not operative.
1 : Click is operative.
0/1
1 1 1
20
13
Function of
prohibiting start
of the sewing
machine by
bobbin thread
counter
Function of prohibiting start of the sewing machine by bobbin thread counting
0 : When counting is out (-1 or less) Function of prohibiting
start of the sewing machine is not operative.
1 : When counting is out (-1 or less) Function of prohibiting start
of the sewing machine after thread trimming is operative.
2 : When counting is out (-1 or less), the sewing machine
stops once. Function of prohibiting start of the sewing
machine after thread trimming is operative.
0 to 2
1 3 0
14
Sewing counter
Counting function of sewing (number of completion of process)
0 : Sewing counter function is not operative.
1 : Sewing counter function is operative.
0/1
1 4 1
20
21
Function of
neutral presser
lifting
Function of lifting presser foot when the pedal is in neutral position.
0 : Function of neutral automatic presser lifting is not opera-
tive.
1 : Selection of function of neutral presser lifting.
0/1
2 1 0
20
22
Function of
changeover of
compensating
switch on the
operation panel
function
Function of needle up/down compensating switch on the opera-
tion panel can be changed.
0 : Needle up/down compensation
1 : One stitch compensation
0/1
2 2 0
20
25
Thread
trimming motion
condition
This function sets the thread trimming motion after DOWN posi-
tion has been off by turning handwheel by hand.
0 : Thread trimming after turning handwheel by hand is permitted.
1 : Thread trimming after turning handwheel by hand is prohib ited.
0/1
2 5 1
20
29
Initial motion
time of back-
tack
This function sets the suction time of initial motion of back-tack
solenoid.
50 to 500
(ms)
2 9 2 5 0
30
Function of
reverse feed
stitching on the
way
Function of reverse feed stitching on the way
0 : Function of reverse stitching on the way is not operative.
1 : Function of reverse feed stitching on the way is operative.
0/1
3 0 0
21
31
Number of
stitches of reverse
feed stitching on
the way
Number of stitches of reverse feed stitching on the way.
0 to 19
(Stitches)
3 1 4
21