Juniper SRX100 - User Manual

SRX100 Services Gateway Quick Start
Use the instructions in this quick start to help you connect the SRX100 Services
Gateway to your network. For details, see the SRX100 Services Gateway Hardware
Guide at
http://www.juniper.net/techpubs/en_US/release-independent/junos/information-products/
pathway-pages/srx-series/product/index.html.
SRX100 Services Gateway Front Panel
SRX100 Services Gateway Back Panel
SRX100 Services Gateway Models
The following model of SRX100 Services Gateway is available:
Connecting and Configuring the SRX Series Device
Use the instructions below to connect and set up the SRX100 Services Gateway to
protect your network. Refer to the LEDs on the front of the device to help you determine
the status of the device.
Overview
The SRX100 Services Gateway requires these basic configuration settings to function
properly:
 Interfaces must be assigned IP addresses.
 Interfaces must be bound to zones.
 Policies must be configured between zones to permit or deny traffic.
 Source NAT rules must be set.
The device has the following default configuration set when you power it on for the first
time. You can use the device without performing any initial configuration.
Factory-Default Settings:
Factory-Default Settings for Security Policies:
Factory-Default Settings for NAT Rules:
Callout Description Callout Description
1 Power button 4 USB port
2 LEDs: ALARM, POWER,
STATUS, HA
5 Console port
3 RESET CONFIG button 6 Fast Ethernet ports
Callout Description Callout Description
1 Lock slot for security cable 3 Cable tie holder
2 Grounding point 4 Power supply input
g031001
Device DDR Memory NAND Flash Memory
SRX100H2 2 GB 2 GB
Port Label Interface Security Zone DHCP State IP Address
0/0 fe-0/0/0 untrust client unassigned
0/1 to 0/7 fe-0/0/1 to fe-0/0/7 trust server 192.168.1.1/24
Source Zone Destination Zone Policy Action
trust untrust permit
trust trust permit
untrust trust deny
Source Zone Destination Zone Policy Action
trust untrust source NAT to untrust zone
interface

Juniper SRX100 Specifications

General

Routing protocols	BGP, IS-IS, MPLS, OSPF
Switching protocols	VLAN 802.1Q, 802.3ad/LACP, STP
Supported network protocols	IPv4, IPv6, CLNS
Firewall security	Yes
Security algorithms	3DES, DES
Authentication method	RADIUS, RSA SecureID, LDAP
VPN support	IPsec VPN
Data transfer rate	0.1 Gbit/s
Input voltage	100 - 240 V
Input frequency	50/60 Hz
Heat dissipation	35 BTU/h
Power requirements	100-240, 50/60
Power over Ethernet (PoE)	No
Power consumption (typical)	30 W
Safety	UL 60950-1, CSA 60950-1, AS / NZS 60950-1, AS / NZS 60950-1, CB Scheme, EN 60950-1
Certification	FCC Class B ICES class B AS / NZS CISPR22 Class B AS / NZS CISPR22 Class B VCCI Class B EN 55022 Class B, EN 300386
Mounting type	Rack mounting
Internal memory	1024 MB
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 40 °C

Weight and Dimensions

Weight	1100 g
Dimensions (WxDxH)	216 x 147 x 36 mm

Summary

SRX100 Services Gateway Front Panel Overview

SRX100 Services Gateway Models Information

Connecting and Configuring the SRX Series Device

Overview of SRX100 Services Gateway Configuration

Task 1: Connect Power Cable

Task 2: Connect Management Device

Task 3: Ensure IP Address Acquisition

Task 4: Access J-Web Interface

Task 5: Select Setup Mode

Task 6: Configure Basic Settings in Default Setup

Task 7: Configure Settings in Guided Setup Mode

Task 8: Apply Basic Configuration

Task 9: Verify Configuration

Powering Off the Device

Using the Reset Config Button

Resetting to Rescue Configuration

Briefly press the Reset Config button to load and commit the rescue configuration.

Resetting to Factory-Default Configuration

Hold the Reset Config button for 15+ seconds to delete all configs and load factory defaults.