Need help?Do you have a question about the Juniper SRX1500 and is the answer not in the manual?
General| IPSec VPN Throughput | 3 Gbps |
|---|---|
| Maximum Concurrent Sessions | 2 million |
| Maximum Firewall Policies | 20, 000 |
| Operating Temperature | 32° to 104° F (0° to 40° C) |
| Form Factor | 1U |
| Throughput | 20 Gbps |
| Interfaces | 16x 1GbE |
| Power Supply | Dual AC power supplies |
| Storage Temperature | -40° to 158° F (-40° to 70° C) |
| Humidity | 90% non-condensing |
Overview of the SRX1500 Services Gateway chassis, including dimensions and mounting in racks.
Details about the front panel, including LEDs, buttons, and ports.
Details about the back panel components, including grounding points, SSD slot, and power supply slots.
Explanation of the services gateway's cooling system, including fan operation and failure.
Details on AC and DC power supplies, their redundancy, and cooling.
Details on the physical dimensions and weight of the SRX1500 Services Gateway.
Required environmental conditions for operation, including temperature, humidity, and noise.
Precautions for ensuring proper operating environment and avoiding equipment failures.
Guidelines and warnings for securely mounting the services gateway in a rack.
Specifications for racks compatible with the SRX1500 Services Gateway.
Details on spacing for mounting brackets and rack flange holes.
Specifications for cabinet size, clearance, and mounting.
Guidelines for ensuring adequate airflow within the cabinet for cooling.
Guidelines for proper electrical wiring to ensure safety and optimal performance.
Information on supported AC power cords, including length limitations.
Pinout details for the MGMT port's RJ-45 Ethernet connector.
Pinout details for the CONSOLE port's RJ-45 serial interface.
Pinout details for the Mini-USB Type-B console port.
Steps for installing the SRX1500 Services Gateway after site preparation.
List of tools and parts needed for the installation process.
Tools and parts needed for unpacking the services gateway.
Procedure for safely unpacking the SRX1500 Services Gateway from its carton.
Steps to prepare the gateway and rack before mounting.
Guidance on securing the rack to the building for stability.
Procedure for physically mounting the gateway into a rack.
Steps for installing an AC power supply unit into the gateway.
Steps for installing a DC power supply unit into the gateway.
Tools and parts needed for grounding the services gateway.
Requirements for grounding the gateway to meet safety and EMI standards.
Procedure for connecting the grounding cable to the chassis.
Tools and parts needed to connect external devices.
Connecting the gateway to a network for out-of-band management via the MGMT port.
Connecting the gateway to a console for management using an RJ-45 cable.
Steps to connect the gateway to an AC power source.
Procedure for connecting the AC power cord to the gateway and power source.
Steps to connect the gateway to a DC power source.
Procedure for powering on the services gateway after installation.
Procedure for powering off the services gateway.
Overview of the Junos OS configuration process for the services gateway.
Details on the default configuration settings applied at the factory.
How to view the factory-default configuration using the CLI.
Procedures for configuring the gateway using the J-Web interface.
How to access the J-Web interface using a web browser.
How to access the command-line interface (CLI) for configuration.
Connecting to the gateway via CLI for out-of-band management.
Step-by-step guide to initial configuration using CLI commands.
List of tools and parts needed for component maintenance.
Regular preventive maintenance tasks to ensure optimal performance.
Specific maintenance tasks for the power supply units.
Overview of methods and tools for troubleshooting.
Diagnosing issues based on chassis and interface alarm messages.
Diagnosing and resolving issues related to the power system.
How to use the reset button to restore factory defaults or rescue configuration.
Configuring the behavior of the reset configuration button.
Tools and parts needed to replace hardware components.
Identification of components that can be replaced on-site.
Procedure for replacing an AC power supply unit.
Steps to safely disconnect the AC power cord.
Procedure for removing an AC power supply unit from the chassis.
Procedure for replacing a DC power supply unit.
Methods to contact Juniper Networks Technical Assistance Center (JTAC) for support.
Procedure for returning a component for repair or replacement.
How to find the chassis serial number and agency labels.
Using CLI commands to list hardware inventory and serial numbers.
Information required when contacting JTAC for support.
Tools and parts needed for packing the gateway for shipment.
Procedure for packing the services gateway for shipping.
Guidelines for packing individual components for shipment.
Explanation of the four safety warning levels used in the guide.
General guidelines to ensure user safety and protect the gateway.
Safety guidelines for working with electrical equipment.
Warning regarding installation in restricted access areas.
Warning that only trained personnel should install or replace the gateway.
Guidelines to minimize ESD damage to sensitive components.
Procedures for fire safety, training, and fire control equipment.
Safety guidelines to prevent eye injury when working around lasers.
Warning specific to Class 1 laser products.
Warning specific to Class 1 LED products.
Warning not to stare into laser beams or use optical instruments.
Warning about invisible radiation from open ports.
Warning about incorrect battery replacement and proper disposal.
Warning not to work on the system during lightning activity.
Warning to remove jewelry before working on powered equipment.
Warning about operating within recommended ambient temperature limits.
Guidelines for proper disposal of the product according to regulations.
Actions to take if an electrical accident results in injury.
General guidelines for safe electrical installation and operation.
Safety guidelines specific to AC-powered services gateways.
Safety guidelines specific to DC-powered services gateways.
List of standards and certifications the gateway complies with.
Information on emitted sound pressure levels per EN ISO 7779.
Details on Electromagnetic Compatibility (EMC) requirements for various regions.
To Next Page
