What to do if my Juniper SRX320 Gateway is not receiving power?
First, check the AC power cord connecting the power source to the device for any damage, and replace it immediately if the insulation is cracked or broken. Next, make sure the power socket you are using is working correctly. Also, verify that the device is receiving an AC input voltage between 100 and 240 VAC.
What to do if my Juniper Gateway boots from an alternate boot device?
If the internal flash memory fails at startup, the Juniper Gateway automatically boots from the alternative boot device (USB storage device). If this is not the intended boot device, reformat the internal flash memory and install a bootable image. If you did not configure the services gateway to boot from an alternative boot device, contact JTAC.
General| Firewall throughput | 1000 Mbit/s |
|---|---|
| Number of users | 50 user(s) |
| Quality of Service (QoS) support | Yes |
| Mobile VPN IPSec | 250 |
| IPS/IDS throughput | 100 Mbit/s |
| USB 2.0 ports quantity | 1 |
| Connectivity technology | Wired |
| SFP module slots quantity | 2 |
| Ethernet LAN (RJ-45) ports | 6 |
| Internal memory | 4000 MB |
| Flash memory | 8000 MB |
| Storage media type | Flash |
| Power consumption (typical) | 27 W |
| Heat dissipation | 157 BTU/h |
| Concurrent connections | 64000 |
| Mean time between failures (MTBF) | 284700 h |
| Storage temperature (T-T) | -20 - 70 °C |
| Operating temperature (T-T) | 0 - 40 °C |
| Storage relative humidity (H-H) | 5 - 95 % |
| Operating relative humidity (H-H) | 10 - 90 % |
| Routing protocols | BGP, CLNS, IS-IS, OSPF, RIP-1, RIP-2 |
Weight and Dimensions| Weight | 1510 g |
|---|---|
| Dimensions (WxDxH) | 299.9 x 43.9 x 191 mm |
Provides an overview of interface modules for SRX300/SRX550 gateways.
Details the Mini-PIMs for SRX300 and SRX550 high memory gateways.
Explains GPIMs and XPIMs for SRX550 high memory services gateways.
Specifies MTU default and maximum values for physical interface modules.
Details Power over Ethernet (PoE) support for SRX550 interfaces.
Introduces the 1-Port Serial Mini-PIM, its features, and standards.
Lists the physical specifications of the Serial Mini-PIM.
Provides an overview of the 1-Port T1/E1 Mini-PIM, its features, and standards.
Lists the network interface specifications for T1 and E1 connections.
Introduces the 1-Port VDSL2 Annex A Mini-PIM and its compatibility.
Lists the hardware specifications for the 1-Port VDSL2 Annex A Mini-PIM.
Provides cable specifications for the 1-Port VDSL2 Annex A Mini-PIM.
Lists interface cables available for the Serial Mini-PIM.
Details EIA-530A DCE cable pinouts for the Serial Mini-PIM.
Guides basic configuration for the Serial Mini-PIM using J-Web or CLI.
Guides basic configuration for the T1/E1 Mini-PIM using J-Web or CLI.
Covers installation and configuration steps for the LTE Mini-PIM.
Details basic configuration for the 8-Port Gigabit Ethernet SFP XPIM.
Guides basic configuration for the 16-Port Gigabit Ethernet XPIM.
Offers guidelines to prevent ESD damage to gateway components.
Step-by-step instructions for removing a Mini-PIM from the gateway.
Step-by-step instructions for installing a Mini-PIM into the gateway.
Provides steps to remove a GPIM from the services gateway.
Provides steps to install a GPIM into the services gateway.
Details how to contact Juniper Networks Technical Assistance Center (JTAC).
Outlines the procedure for returning hardware components for repair/replacement.
To Next Page
