E
Eduardo GardnerSep 7, 2025
What to do if sounds are intermittently distorted by outside noise on my JVC RX-F10S Receiver?
- BbreannasmithSep 7, 2025
This is not a malfunction.
To Next PageTo Next PageWhat to do if sounds are intermittently distorted by outside noise on my JVC RX-F10S Receiver?
This is not a malfunction.
Why is my JVC RX-F10S Receiver remote control not operating correctly?
If the remote control of your JVC Receiver does not operate as intended, it might not be ready for your intended operation. Set the mode selector correctly, then press the corresponding source selecting button or SOUND before operation.
What to do if my JVC RX-F10S remote control does not work?
If your JVC Receiver remote control isn't working, consider these potential causes: * There may be an obstruction hiding the remote sensor on the receiver. Remove any obstructions. * The batteries might be weak. Replace the batteries. * The mode selector could be set to the incorrect position. Ensure the mode selector is in the proper position.
Why does my JVC Receiver remote control not operate as I intend?
The remote control may not be ready for your intended operation. Set the mode selector correctly, then press the corresponding source selecting button or SOUND before operation.
What to do if there is no sound from my JVC Receiver speakers?
If there is no sound coming from the speakers of your JVC Receiver, first ensure the speaker signal cables are correctly connected. Check all audio connections to confirm they are properly set up. Make sure that you have selected the correct source on your receiver. Verify that muting is not activated by pressing the MUTING button. Confirm that the input mode (analog or digital) is correctly selected. Finally, check if TV Direct is activated and deactivate it if necessary.
Why does my JVC RX-F10S turn off by itself?
If your JVC Receiver turns off and enters standby mode, it could be due to several reasons. The speakers might be overloaded because of high volume, so stop the playback source. Alternatively, there might be a short circuit at the speaker terminals; in this case, check the speaker wiring. If the wiring is not short-circuited, contact your dealer. It is also possible that the receiver is overloaded because of high voltage, if so, consult your dealer after unplugging the power cord.
What to do if “OVER HEAT” flashes on the display and JVC Receiver turns off?
If “OVER HEAT” flashes on the display and the receiver turns off, it's likely overloaded due to high volume or long time usage. Turn the receiver on again. If it turns off soon after, consult your dealer after unplugging the power cord.
Why does my JVC RX-F10S Receiver have no sound from speakers?
Several factors could be the reason: * Speaker signal cables might not be connected. Check the speaker wiring and reconnect if necessary. * Connections might be incorrect. Review the audio connections. * The wrong source might be selected. Ensure you've selected the correct source. * Muting could be activated. Press the MUTING button to cancel the mute. * An incorrect input mode (analogue or digital) might be selected. Choose the correct input mode. * TV Direct might be activated. Deactivate TV Direct.
Why is bass sound reinforced too much on my JVC RX-F10S?
If the bass sound is reinforced too much when listening in stereo on your JVC Receiver, the appropriate bass level might not be selected. Adjust the audio position level.
Why can't I use the buttons on my JVC RX-F10S?
If the buttons on your JVC Receiver cannot be used, TV Direct might be activated. Deactivate TV Direct to enable the buttons.
General| Weight | 10.2kg |
|---|---|
| Preset Stations | 30 |
| Power output | 100 watts per channel |
| Total harmonic distortion | 0.8% (1 kHz) |
| Input sensitivity | 200 mV/47 kOhms (line) |
| Signal to noise ratio | 95dB (line) |
| Output | 200mV (line) |
| Video Connections | composite |
| Amplifier Type | Digital |
| RMS Power per Channel (8 Ohms, 20Hz-20kHz) | 100W |
| THD | 0.8% |
| Signal-to-Noise Ratio | 100dB (line) |
| Tuner Type | Digital |
