KEB 7608000-4001

10
STANDARDS FOR ASYNCHRONOUS AND SYNCHRONOUS MOTORS
Standards for asynchronous and synchronous motors
DGUV regulation 3 Electrical installations and equipment
DIN 46228-1 Tubular end-sleeves without plastic sleeve
DIN 46228-4 Tubular end-sleeves with plastic sleeve
DIN IEC 60364-5-54 Low-voltage electrical installations - Part 5-54: Selection and erection of
electrical equipment - Earthing arrangements, protective conductors and protec-
tive bonding conductors
EN 60204-1 Safety of machinery - Electrical equipment of machines - Part 1: General requi-
rements (IEC 44/709/CDV)
EN 60439-1 Low-voltage switchgear and controlgear assemblies - Part 1: Type-tested and
partially type-tested assemblies (IEC 60439-1)
EN 60529 Degrees of protection provided by enclosures (IP Code) (IEC 60529)
EN 60664-1 Insulation coordination for equipment within low-voltage systems - Part 1:
Principles, requirements and tests (IEC 60664-1)
EN60721-3-1 Classicationofenvironmentalconditions-Part3:Classicationofgroupsof
environmental parameters and their severities - Section 1: Storage (IEC 104/648/CD)
EN60721-3-2 Classicationofenvironmentalconditions-Part3:Classicationofgroupsof
environmental parameters and their severities - Section 2: Transportation and
handling (IEC 104/670/CD)
EN60721-3-3 Classicationofenvironmentalconditions-Part3:Classicationofgroupsof
environmentalparametersandtheirseverities;section3:Stationaryuseat
weatherprotected locations (IEC 60721-3-3)
EN 61800-2 Adjustable speed electrical power drive systems - Part 2: General requirements
-Ratingspecicationsforlowvoltageadjustablespeeda.c.powerdrivesystems
(IEC 61800-2)
EN 61800-3 Adjustable speed electrical power drive systems - Part 3: EMC requirements
andspecictestmethods(IEC22G/297A/CD)
EN 61800-5-1 Adjustable speed electrical power drive systems - Part 5-1: Safety requirements
- Electrical, thermal and energy (IEC 61800-5-1)
UL 61800-5-1 American version of the EN 61800-5-1 with „National Deviations“
EN 60034-1 Rotating electrical machines - Part 1: Rating and performance (IEC 2/1768/CD)
EN60034-2-3 Rotatingelectricalmachines-Part2-3:Specictestmethodsfordetermining
lossesandefciencyofconverter-fedACmotors(IEC2/1841/CD)
EN 60034-5 Rotating electrical machines - Part 5: Degrees of protection provided by integral
designofrotatingelectricalmachines(IPcode)-Classication(IEC60034-5)
EN 60034-6 Rotating electrical machines - Part 6: Methods of cooling (IC-Code) (IEC 60034-6)
EN60034-7 Rotatingelectricalmachines-Part7:Classicationoftypesofconstruction,
mounting arrangements and terminal box position (IM code) (IEC 60034-7)
EN 60034-8 Rotating electrical machines - Part 8: Terminal markings and direction of rotation
(IEC 60034-8)
EN 60034-9 Rotating electrical machines - Part 9: Noise limits (IEC 60034-9)
EN 60034-11 Rotating electrical machines - Part 11: Thermal protection (IEC 60034-11)
EN 60034-14 Rotating electrical machines - Part 14: Mechanical vibration of certain machines
with shaft heights 56 mm and higher - Measurement, evaluation and limits of
vibration severity (IEC 60034-14)
IEC/TS 60034-17 Rotating electrical machines - Part 17: Cage induction motors when fed from
converters - Application guide (IEC/TS 60034-17)
EN 60034-18-41 Rotating electrical machines - Part 18-41: Partial discharge free electrical