Need help?Do you have a question about the Kenwood TM-D710E and is the answer not in the manual?
General| Frequency Range (TX) | 144-146 MHz, 430-440 MHz |
|---|---|
| Output Power (VHF) | 50 W |
| Display | LCD |
| Memory Channels | 1000 |
| GPS | Built-in |
| Voltage | 13.8 V DC |
| Antenna Impedance | 50 ohms |
| Type | Dual Band Mobile Transceiver |
| Modes | FM, AM |
| APRS | Built-in |
| Packet | 1200/9600 bps |
| RF Power Output | 50 W |
Explains how to access repeaters with standard or non-standard offsets and tones.
Describes how to set transmit frequency higher or lower than receive frequency.
Details setting the offset frequency value for transmit frequency adjustments.
Explains how to turn the Tone function ON or OFF for repeater access.
Guides on storing simplex and standard repeater frequencies into memory channels.
Details storing odd-split repeater frequencies with non-standard offsets.
Explains how to retrieve stored memory channels and data.
Details the procedure for saving transceiver settings into PM channels.
Explains how to retrieve and apply saved configurations from PM channels.
Monitors all tunable frequencies on the current band using the current frequency step size.
Monitors all programmed memory channels for active signals.
Monitors specific groups of memory channels (100 channels per group).
Scans a selected frequency range within memory channels, similar to VFO Scan.
Monitors a 1 MHz segment of the band using the current frequency step size.
Monitors the Call channel and the currently selected VFO or Memory channel.
Graphically displays frequencies near the current operating frequency and their activity.
Explains how to activate and set CTCSS for selective calls from specific persons.
Scans CTCSS frequencies to identify the incoming tone on a received signal.
Guides on activating and selecting DCS codes for selective calls.
Scans DCS codes to identify the incoming DCS code on a received signal.
Explains how to send DTMF tones manually by pressing keypad keys.
Introduces the 10 dedicated DTMF Memory channels for storing codes.
Guides on saving DTMF codes into the transceiver's memory channels.
Explains how to transmit DTMF codes stored in memory channels.
Details storing EchoLink data into dedicated DTMF memory channels.
Explains how to transmit stored EchoLink memory data.
Explains how to connect the transceiver to a PC for EchoLink Sysop mode.
Explains entering and operating in Packet mode using the built-in TNC.
Monitors DX PacketClusters for received DX information and latest data.
Lists available TNC commands, their short forms, descriptions, parameters, and defaults.
Explains APRS format for data communication with GPS receiver or manual position entry.
Guides on setting callsign and beacon type (APRS/NAVITRA) for beacon creation.
Details GPS receiver settings, including port and manual position data entry.
Guides on displaying only specified types of data from the station list.
Explains how to enter a callsign and message to transmit.
Details how to transmit messages from the message list or manually.
Guides on programming your callsign and SSID for APRS transmissions.
Selects input type for APRS communications (GPS, Weather, or OFF).
Explains how to embed frequency information in position beacons for QSY.
Sets whether to digipeat packets that include your callsign in the path.
Sets automatic reply messages with selectable delay times.
Monitors DX PacketClusters for received DX information and latest data.
Sets the repeater operation mode to Cross-band, Locked TX:A-BAND, or Locked TX:B-BAND.
Outlines the necessary preparation steps for wireless remote control.
Explains how handheld DTMF keys function as control commands in Remote Control mode.
Guides on turning the Weather Alert function ON or OFF.
Provides instructions for connecting the transporter to an HF transceiver.
Explains how microphone keys control the Transporter via the Commander.
To Next Page
