To Next PageTo Next PageWhat to do if Kenwood Transceiver memory scan will not scan one of the stored channels?
If Memory Scan will not scan one of the stored channels, and the desired channel is NOT locked out, with Group Scan selected, the channel you want to scan may be in a different group. Select the group that contains the memory channel you want to scan.
Why Kenwood Transceiver no signals are received S-meter is reading full scale?
If no signals are received and the S-meter is reading full scale, the RF control may be set too low. Turn the RF control fully clockwise.
What to do if Kenwood TS-2000 attempting to transmit results in the “HELLO” message appearing?
If attempting to transmit results in the “HELLO” message appearing, first check the antenna connection and correct as necessary. Second, reduce the SWR of the antenna system. Third, correct the input voltage or use a 12 to 16V battery. Fourth, use the provided or an optional DC power cable.
Why does Kenwood Transceiver reset to factory default?
If the internal TNC resets to the factory default values after switching ON the Kenwood Transceiver, the internal TNC backup lithium battery voltage is likely too low. Have a new battery installed by your dealer or at aKKKKKEEEEENNNNNWWWWWOOOOOOOOOODDDDDService Center.
What to do if Kenwood TS-2000 Transceiver internal tuner is bypassed immediately after tuning is started?
If the internal tuner is bypassed immediately after tuning starts, the SWR of the antenna system may be too high. Adjust the antenna system to lower the SWR.
What to do if Kenwood Transceiver program scan will not start scanning?
If Program Scan will not start scanning, the start and end frequencies may be identical. Store different start and end frequencies.
What to do if Kenwood TS-2000 Transceiver memory scan will not start scanning?
If Memory Scan won't start, first, adjust the SQL control to just eliminate background noise. Second, ensure at least two memory channels are unlocked. Third, make sure data is stored in at least two memory channels.
Why Kenwood TS-2000 SSB audio quality is very poor?
Poor SSB audio quality may be due to several factors. First, check if the filter for digital operation is selected and, if so, change Menu No. 32 to OFF. Second, adjust the DSP SLOPE (LOW) control counterclockwise and the DSP SLOPE (HIGH) control clockwise. Third, ensure Noise Reduction 1 or 2 is OFF by pressing [N.R.]. Finally, verify Beat Cancel is OFF by pressing [B.C.].
Why Kenwood Transceiver frequency cannot be changed?
The Frequency Lock function may be ON. Press [F.LOCK] to switch OFF the function.
What to do if Kenwood TS-2000 no signals are received?
If no signals are received or receive sensitivity seems poor, check the following: * Ensure the SQL control is not fully clockwise; turn it counterclockwise. * Verify the Attenuator function is OFF by pressing [ATT]. * Make sure [SEND] is not pressed, which puts the transceiver in transmit mode; press [SEND] to return to receive mode. * Release Mic [PTT]. * Press [ANT] to select the other antenna connector. * Press [PRE-AMP] to switch ON function.
General| Antenna Impedance | 50 ohms |
|---|---|
| Supply Voltage | 13.8V DC ±15% |
| Current Drain TX | 20.5A |
| Receiver Type | Triple Conversion Superheterodyne |
| Modes | SSB, CW, AM, FM, FSK |
| Type | Base Station |
| Frequency Range TX | 0.1-60 MHz (HF), 144-148 MHz (VHF), 430-450 MHz (UHF) |
| Image Rejection | More than 70 dB |
| Selectivity | 2.4 kHz (SSB), 500 Hz (CW), 15 kHz (FM) |
| Antenna Connector | SO-239 |
| Frequency Range | HF/6m/2m/70cm |
